User Tag List
Thanks: 
Likes: 0
Results 1 to 9 of 9
Thread: STV Euro ??
-
03-17-2018, 02:07 PM #1
5000 RPM
- Join Date
- Jan 2013
- Location
- GA
- Posts
- 212
- Thanks (Given)
- 35
- Thanks (Received)
- 10
- Likes (Given)
- 43
- Likes (Received)
- 32
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
STV Euro ??
Hi, I'm working on a similar hull and wonder if someone can tell me the built in setback from the pad to transome on a STV Euro. Thanks
Speed cost money. How fast you wanna go?
I have done so much with so little for so long, I can now do the impossible with nothing!
-
03-18-2018, 08:59 AM #2
6000 RPM
- Join Date
- May 2001
- Location
- Maine
- Posts
- 1,091
- Thanks (Given)
- 13
- Thanks (Received)
- 42
- Likes (Given)
- 105
- Likes (Received)
- 213
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Are you looking for the vertical distance from the bottom of the pad (just below the drain plug) to the bottom of the built in set back?
OR...
The horizontal distance from the transom to where the motor or jack plate bolt on?
-
03-18-2018, 10:58 AM #3
5000 RPM
- Join Date
- Jan 2013
- Location
- GA
- Posts
- 212
- Thanks (Given)
- 35
- Thanks (Received)
- 10
- Likes (Given)
- 43
- Likes (Received)
- 32
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Horizontal distance Thanks
Speed cost money. How fast you wanna go?
I have done so much with so little for so long, I can now do the impossible with nothing!
-
03-18-2018, 11:01 AM #4
5000 RPM
- Join Date
- Jan 2013
- Location
- GA
- Posts
- 212
- Thanks (Given)
- 35
- Thanks (Received)
- 10
- Likes (Given)
- 43
- Likes (Received)
- 32
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Horizontal from end of pad to transom where motor or plate bolts
Speed cost money. How fast you wanna go?
I have done so much with so little for so long, I can now do the impossible with nothing!
-
03-19-2018, 06:11 PM #5
6000 RPM
- Join Date
- May 2001
- Location
- Maine
- Posts
- 1,091
- Thanks (Given)
- 13
- Thanks (Received)
- 42
- Likes (Given)
- 105
- Likes (Received)
- 213
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I will get you the measurement in the AM as I have the boat in the garage.
-
03-19-2018, 10:06 PM #6
5000 RPM
- Join Date
- Jan 2013
- Location
- GA
- Posts
- 212
- Thanks (Given)
- 35
- Thanks (Received)
- 10
- Likes (Given)
- 43
- Likes (Received)
- 32
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Many thanks.
Originally Posted by 4Speed
Speed cost money. How fast you wanna go?
I have done so much with so little for so long, I can now do the impossible with nothing!
-
03-20-2018, 07:17 PM #7
6000 RPM
- Join Date
- May 2001
- Location
- Maine
- Posts
- 1,091
- Thanks (Given)
- 13
- Thanks (Received)
- 42
- Likes (Given)
- 105
- Likes (Received)
- 213
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
At the top it looks like about 15"
-
One Oldman thanked for this post
-
03-20-2018, 08:33 PM #8
5000 RPM
- Join Date
- Jan 2013
- Location
- GA
- Posts
- 212
- Thanks (Given)
- 35
- Thanks (Received)
- 10
- Likes (Given)
- 43
- Likes (Received)
- 32
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Thank you! That gives a figure to start with. The reason for all this is the boat I have is a VT200 Shadow and most of the people I've found are running 12-14" jack plates with 2.4 and 2.5 motors. Well I got to looking at STV setups and it looks like a lot of them are only running 4-6" plates. I will be running a 3.0 motor so I have a lot of things to consider. It became obvious that the first place I should look was if there is difference in the built in set back. Thank you so much. Originally Posted by 4Speed
At the top it looks like about 15"
Speed cost money. How fast you wanna go?
I have done so much with so little for so long, I can now do the impossible with nothing!
-
03-21-2018, 07:22 PM #9
5000 RPM
- Join Date
- Jan 2013
- Location
- GA
- Posts
- 212
- Thanks (Given)
- 35
- Thanks (Received)
- 10
- Likes (Given)
- 43
- Likes (Received)
- 32
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
From my pad bottom to the bottom edge of the transom is around 9". If it's around 15" on the STV it explains the reason for the different sized jack plates on the two similar hulls. Thanks
Speed cost money. How fast you wanna go?
I have done so much with so little for so long, I can now do the impossible with nothing!
Reply With QuoteSimilar Threads
-
Looking for a Stv Euro
By kylemclaughlin in forum Hulls WantedReplies: 2Last Post: 03-29-2014, 10:16 AM -
stv euro
By spearhunter7 in forum Props, Setup, and RiggingReplies: 21Last Post: 03-19-2014, 10:02 PM -
Euro-ski, more MPH ?
By wembley in forum General Boating DiscussionReplies: 18Last Post: 07-07-2004, 12:59 PM -
anyone following the Euro Cup?
By Pete in forum The Scream And Fly LoungeReplies: 0Last Post: 06-24-2004, 06:38 PM
