Activity Stream - Scream And Fly Powerboat and High Performance Powerboating Discussion Forums

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles Blog Blogs

Today, 11:09 AM

Forkin' Crazy replied to a thread Sierra. This looks fun. in The Scream And Fly Lounge

I bet every bit of that before options!!! Amazing what they can build now.

2 replies | 87 view(s)

Today, 11:06 AM

Euroski replied to a thread Video: Cat almost becomes a submarine! in General Boating Discussion

Is it always that rough there?

2 replies | 41 view(s)

Today, 10:47 AM

Jim Bryan replied to a thread New to Scream and Fly in General Boating Discussion

just a few pounds more than the 300 Promax I have now

10 replies | 274 view(s)

Today, 10:47 AM

rckid74 replied to a thread Merc V6 History in Outboard and Racing History

hi dave -- yea i'm still around lurking in the shadows, watching what all's going on. -- first of all understand that the v6 (even with the balance...

672 replies | 355784 view(s)

Today, 10:46 AM

CUDA replied to a thread Video: Cat almost becomes a submarine! in General Boating Discussion

Yeah I posted that under 32 wide body, the 32 is the same hull made wider and a tad longer, they closed up the front some to pack more air which...

2 replies | 41 view(s)

Today, 10:43 AM

Jim Bryan replied to a thread New to Scream and Fly in General Boating Discussion

yes the tower works good

10 replies | 274 view(s)

Today, 10:42 AM

ChrisCarsonMarine replied to a thread Mercury Tech: CCM intake stuffers for 2.4 200 carb mota in Technical Discussion

The stuffers for the 5 petal cages will net you the same gain as 060 off the front half,the spacer is good for holeshot and midrange,make sure it...

1 replies | 33 view(s)

Today, 10:40 AM

Jim Bryan replied to a thread New to Scream and Fly in General Boating Discussion

the best I have seen so far is 78 MPH but hope to get over 80 with new motor

10 replies | 274 view(s)

Today, 10:28 AM

at100plus replied to a thread Lifeline (Large) Used clean good condition- not certified. in Misc. Parts and Accessories

I replied to your PM.

2 replies | 193 view(s)

Today, 10:23 AM

Scream And Fly started a thread Video: Cat almost becomes a submarine! in General Boating Discussion

At the infamous Haulover Inlet.

2 replies | 41 view(s)

Today, 10:16 AM

FUJIMO replied to a thread Mercury Through The Years... in Outboard and Racing History

21064 replies | 1371885 view(s)

Today, 10:12 AM

FUJIMO replied to a thread Mercury Through The Years... in Outboard and Racing History

21064 replies | 1371885 view(s)

Today, 10:09 AM

FUJIMO replied to a thread Mercury Through The Years... in Outboard and Racing History

21064 replies | 1371885 view(s)

Today, 10:03 AM

lars strom replied to a thread Facts about Evinrude/Johnson racing outboards made my OMC in Outboard and Racing History

True love.. A decal from Scandinavia back when I was an exclusive Evinrude dealer/racer.

8318 replies | 1349425 view(s)

Today, 09:47 AM

FUJIMO replied to a thread Mercury Through The Years... in Outboard and Racing History

21064 replies | 1371885 view(s)

Today, 09:45 AM

FUJIMO replied to a thread Tricks that old racers get up to after retirement in Outboard and Racing History

...but who came out on top. molinari.

13770 replies | 1092776 view(s)

Today, 09:43 AM

FUJIMO replied to a thread 300x sportmaster repair in General Boating Discussion

...this is a case of...a new case...;)

4 replies | 138 view(s)

Today, 09:41 AM

Chaz replied to a thread Four Stroke outboards have changed the performance boating landscape in General Boating Discussion

As are you Brad .. :smiletest: Negative ... only about things I don't like . I love the USA , just not our government. Please explain the diff...

53 replies | 2053 view(s)

Today, 09:40 AM

Smalltownbassin replied to a thread Mercury Tech: '87 2.4L CARB to EFI conversion? in Technical Discussion

Just to fill you in on what i read in some of the archives, it all depends on the reed configuration. Vertical reeds = NOPE, horizontal reeds = MAYBE...

2 replies | 62 view(s)

Today, 09:39 AM

FUJIMO replied to a thread Mercury Tech: $60 for a rod bearing? WTH??? in Technical Discussion

...nothings changed really. us older folks remember this from back in the seventies when we were into our street rod cars & working on them. it was...

5 replies | 141 view(s)

Today, 09:25 AM

Chaz replied to a thread Mercury Tech: $60 for a rod bearing? WTH??? in Technical Discussion

It's the same good people who will sell you a dozen small O-rings for $400.00 Now that you spoke bad about them and their price structure ......

5 replies | 141 view(s)

Today, 09:21 AM

Chaz replied to a thread 300x sportmaster repair in General Boating Discussion

I was working on making a "sweat in" and weld in place cartridge. Not a whole lot of meat in that upper bearing / nut area .. so i dropped the...

4 replies | 138 view(s)

Today, 09:19 AM

rgsauger replied to a thread Mercury Tech: '87 2.4L CARB to EFI conversion? in Technical Discussion

subscribed

2 replies | 62 view(s)

Today, 09:18 AM

rgsauger started a thread Mercury Tech: CCM intake stuffers for 2.4 200 carb mota in Technical Discussion

Putting this thing back together. already have the CCM reeds (nice) and wondering about the stuffers. Front half is not cut. Would I see a...

1 replies | 33 view(s)

Today, 09:17 AM

Chaz replied to a thread Boat crash twice second one even better... in General Boating Discussion

I think it could be the "Gumby green" captain that had it favoring the left ... :D

4 replies | 290 view(s)

Today, 09:14 AM

rgsauger replied to a thread Mercury Tech: $60 for a rod bearing? WTH??? in Technical Discussion

Actually...I just bought one new piston because the others are good. I don't know that the bearing is bad but I figured if it was up against a...

5 replies | 141 view(s)