Screaming Eagle Boats New Edge 22 Cat

**XstreamVking** · 03-18-2017, 07:54 PM

Basically did it the same as you are. Fabricated metal frames, bolted the hull to them, and then cut it apart and slid the framed hull pcs on U channel rails bolted to the floor with forklifts. Hard work for sure..

**capteliminator** · 03-18-2017, 08:21 PM

Looks great keep the info and pics coming!!

**JPEROG** · 03-18-2017, 09:13 PM

You guys are cranking. It has taken me a long time to get mine just a few steps ahead of where you guys are at. This is one of several projects that I have going so it is far from full time or attention but its been in process for what seems like forever. The deck should be faired in and done next week then we will attack the body work before it goes back upside down and install the new experimental running surface. This is all a ton of work for an old boat but it will be one of a kind when its done-I just hope it runs like we are thinking. You can see in the pictures that its just a touch beyond what it should be for width but I wasn't going through all of this without getting at least this width out of it.

Click image for larger version.

Name: Cut 1.jpg
Views: 235
Size: 233.3 KB
ID: 369960

Click image for larger version.

Name: Cut 2.jpg
Views: 218
Size: 184.3 KB
ID: 369961

Click image for larger version.

Name: cut 4.jpg
Views: 196
Size: 31.0 KB
ID: 369962

Click image for larger version.

Name: cut 5.jpg
Views: 203
Size: 427.4 KB
ID: 369963

Click image for larger version.

Name: cut 6.jpg
Views: 223
Size: 419.9 KB
ID: 369964

Click image for larger version.

Name: cut 7.jpg
Views: 186
Size: 434.0 KB
ID: 369965

.

Click image for larger version.

Name: cut 8.jpg
Views: 181
Size: 427.5 KB
ID: 369966

Joe

**Spectre Powerboats** · 03-18-2017, 09:46 PM

Joe, looks good and familiar. Wait to you see what we did with a 24. It is going through the same steps as the 21, but we have to finish the 21 first.

**JPEROG** · 03-18-2017, 09:48 PM

I would have been miles ahead just waiting for you to do it. Are you adding the strake up front like we discussed?

Joe

**Spectre Powerboats** · 03-18-2017, 10:07 PM

Originally Posted by JPEROG

I would have been miles ahead just waiting for you to do it. Are you adding the strake up front like we discussed?

Joe

No, I am building these more like an F1 bottom versus the traditional step bottoms.

**JPEROG** · 03-18-2017, 10:15 PM

Let me know when you get started. I will most likely stop by to see you guys on our way to Three Lakes in June.

Joe

**Spectre Powerboats** · 03-18-2017, 10:17 PM

Damn it Joe, I was trying to save some of this for future write ups. We are even re-working a 28, but since Pete is starting to build them again, we will NOT be make a mold off it. I will start another post about this project at a later date.

Click image for larger version.

Name: IMG_8411.JPG
Views: 201
Size: 119.0 KB
ID: 369972

Click image for larger version.

Name: IMG_8412.JPG
Views: 176
Size: 125.1 KB
ID: 369973

**berdes** · 03-18-2017, 10:30 PM

Doing a 24 too ? You guy's are AMAZING ! So what is the estimated sales availability time on these projects ?
Oh yeah- subscribed also.

**JPEROG** · 03-18-2017, 10:51 PM

Originally Posted by Screaming Eagle Boats

Damn it Joe, I was trying to save some of this for future write ups. We are even re-working a 28, but since Pete is starting to build them again, we will NOT be make a mold off it. I will start another post about this project at a later date.

Is this the one that I like so much?

Joe

**Spectre Powerboats** · 03-18-2017, 11:11 PM

Originally Posted by JPEROG

Is this the one that I like so much?

Joe

No, that one is to nice to cut on.

**Spectre Powerboats** · 03-18-2017, 11:20 PM

Originally Posted by berdes

Doing a 24 too ? You guy's are AMAZING ! So what is the estimated sales availability time on these projects ?
Oh yeah- subscribed also.

The first Edge 22 is sold, the second ones build slot will be in the fall. The 24 that will be a 25 will be able in the winter. Will post each project as they unfold.

**Risco** · 03-19-2017, 07:11 AM

Originally Posted by Screaming Eagle Boats

Damn it Joe, I was trying to save some of this for future write ups. We are even re-working a 28, but since Pete is starting to build them again, we will NOT be make a mold off it. I will start another post about this project at a later date.

Whats the reasoning behind taking the steps out ?

**Spectre Powerboats** · 03-19-2017, 09:35 AM

Originally Posted by Risco

Whats the reasoning behind taking the steps out ?

Not removing all of them, it is more of a design change. We have been able to modify the bottoms to reduce the porpoise hugely in the 24's and 28's and gain another 2-3 mph on top end.

**Risco** · 03-19-2017, 09:52 AM

Originally Posted by Screaming Eagle Boats

Not removing all of them, it is more of a design change. We have been able to modify the bottoms to reduce the porpoise hugely in the 24's and 28's and gain another 2-3 mph on top end.

Sounds good does it affect the rough water ride? I like the staggered Chines that makes a lot of sense to me. Love the work you guys are doing and sounds like I'll be trying to squeeze another boat in the garage.