User Tag List
Likes: 0
Results 1 to 6 of 6
-
06-04-2023, 09:02 AM #1Junior Member
- Join Date
- Aug 2008
- Location
- Jacksonville
- Posts
- 12
- Thanks (Given)
- 4
- Thanks (Received)
- 0
- Likes (Given)
- 1
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Mercury ProMax 225 Bushing / Sleeve - Need Help Identifying Placement
Hello,
I installed new reeds and thought I adequately documented what goes where as I disassemble but apparently not good enough. Can anyone help with where this bushing is supposed to go? I’m not sure whether to refer to it as a bushing or a sleeve and can’t find a schematic showing it.
Thanks for any help!
Haydon
-
06-04-2023, 10:19 AM #2
Remove VST mounting bolts, may have fallen out of one of the rubber bushings.
Dave1980 Cougar 19 tunnel,90 2.4L Bridgeport EFI in middle of restoration.
1988 BAJA Sunsport 186, 96 225 Pro Max
79 12' Auminum, 95 Merc 9.9
RIP Stu
"So many idiots, so few bullets"
-
jaxflats thanked for this post
-
06-04-2023, 10:41 AM #3Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,753
- Thanks (Given)
- 381
- Thanks (Received)
- 1305
- Likes (Given)
- 5602
- Likes (Received)
- 11033
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
Spacer between switch boxes?
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
-
jaxflats thanked for this post
-
06-04-2023, 11:36 AM #4Junior Member
- Join Date
- Aug 2008
- Location
- Jacksonville
- Posts
- 12
- Thanks (Given)
- 4
- Thanks (Received)
- 0
- Likes (Given)
- 1
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Thanks, I think it did go with the VST mounting. I really appreciate it.
-
06-04-2023, 11:48 AM #5Junior Member
- Join Date
- Aug 2008
- Location
- Jacksonville
- Posts
- 12
- Thanks (Given)
- 4
- Thanks (Received)
- 0
- Likes (Given)
- 1
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
One other question, what is the name/type of part of the straight black plastic part with the Phillips Head screw in the bottom right of the photo of the outboard? Thanks Again
-
06-04-2023, 01:14 PM #65000 RPM
- Join Date
- Mar 2023
- Location
- SW Florida
- Posts
- 479
- Thanks (Given)
- 3
- Thanks (Received)
- 28
- Likes (Given)
- 1
- Likes (Received)
- 76
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
jax. open the second thread. hit edit. hit delete 3 diff places and it will be gone.
-
jaxflats thanked for this post
Similar Threads
-
Oil Pump Drive Bushing for 225 Promax
By ssntmd8r in forum Parts WantedReplies: 0Last Post: 05-27-2018, 04:04 PM -
I need help identifying the lower on this 300 promax
By BigKiddd in forum Technical DiscussionReplies: 4Last Post: 07-02-2015, 05:27 AM -
What sleeve is this? Suppose to be a 225 promax.
By WaterBoy in forum Technical DiscussionReplies: 9Last Post: 08-24-2014, 10:14 PM -
Mercury Tech: 2.5 Mercury EGT probe placement
By jhelmly in forum Technical DiscussionReplies: 13Last Post: 06-04-2011, 09:11 PM -
Mercury Tech: 225 ProMax Sleeve question
By TheRickster in forum Technical DiscussionReplies: 2Last Post: 07-24-2008, 07:12 PM