User Tag List
Likes: 0
Results 1 to 3 of 3
-
05-24-2023, 08:51 AM #1New Member
- Join Date
- May 2023
- Location
- Chicago, IL
- Posts
- 1
- Thanks (Given)
- 2
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Ideal Jack Plate Setback for Stratos 210 Elite /w Yamaha 250 HP VMAX HPDI ?
I currently have a manual jack plate with a 10" setback on my Stratos 210 Elite /w Yamaha 250 HP VMAX HPDI. I'm looking to replace it with a hydraulic jack plate.
For those who have a Stratos 210 Elite or similar Champion, any recommendations on what jack plate setback would be best?
With my current setup, I get a decent amount of bow lift. Like when slowing down after high speeds and trying to run slow, the bow sits pretty high even after trimming the motor down. High enough to where I can’t see ahead. I basically have to almost come to a complete stop and let the boat settle, and then start moving again in order for the bow to stay down so that I can see ahead. Porpoising is another problem I have.
I think part of the problem is the motor sits too low, but I can't raise the manual jack plate any higher.
I was originally thinking of a 12" setback but now I'm reconsidering since I believe a larger setback will make the bow lift worse. But on the other hand, perhaps a hydraulic jack plate would give me more flexibility to prevent the issue.
But I'm thinking a 10" setback or even and 8" setback might be better option for my issues and also put less stress on the transom.
So I'd like to hear what setbacks people with similar boats are running with and recommendations.
-
05-24-2023, 09:04 AM #2
Stick with a 10", and add a drag plate, (hydrofoil) to the cavitation plate.
-
ciminoj thanked for this post
-
05-25-2023, 11:50 AM #3Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,753
- Thanks (Given)
- 381
- Thanks (Received)
- 1302
- Likes (Given)
- 5602
- Likes (Received)
- 11031
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
Hyd. jack plates work wonders too...Set back is good up to a point. Once the balance point gets too far back, then the problems you describe occur.
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
-
ciminoj thanked for this post
Similar Threads
-
Yamaha 300 Vmax hpdi
By ra4577 in forum Outboard EnginesReplies: 0Last Post: 05-21-2017, 06:57 PM -
Yamaha 3.3 200 VMAX Hpdi
By Coupe9050lx in forum Technical DiscussionReplies: 12Last Post: 03-11-2010, 10:36 AM -
Yamaha 06 Vmax HPDI Hesitation
By squirrely in forum Technical DiscussionReplies: 5Last Post: 10-25-2009, 10:07 PM -
2006 294 stratos w/200 yamaha HPDI
By luckycraft in forum Props, Setup, and RiggingReplies: 0Last Post: 06-17-2006, 09:04 PM -
2006 295 stratos with 200 yamaha HPDI
By luckycraft in forum General Boating DiscussionReplies: 0Last Post: 06-17-2006, 08:57 PM