User Tag List
Results 1 to 15 of 34
Thread: 1983 vector
-
01-10-2023, 01:54 PM #1Junior Member
- Join Date
- Sep 2021
- Location
- South Louisiana
- Posts
- 21
- Thanks (Given)
- 3
- Thanks (Received)
- 0
- Likes (Given)
- 3
- Likes (Received)
- 14
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
1983 vector
Got the boat in July of 2021 and started gutting to rebuild. Built a jig to set it on and started cutting out transom, old core, stringer box and foam boxes and ground entire hull down with a brazed cup wheel and 36grit wheels on a 4 inch grinder. For transom replacement i used 3 half inch thick pieces of marine plywood bonded together with a wet layer of csm. Then put in a layer of 1808 where transom will fit then bonded the new transom in with a layer of csm. Covered that with 3 layers of 1808. Was going to delete the splashwell but being i kept the piece i cut out i decided to put it back in for its functionality. Once that was done i laid a layer of 1808 threw out the hull. Now im putting 1/2 inch balsa core in, started up in the wings and then did the pad. Bonded everything in with 2 wet layers of csm and covered with 1808. Thats where im at now, hopefully i can get the rest of the core in soon!
-
01-10-2023, 02:30 PM #2Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,753
- Thanks (Given)
- 381
- Thanks (Received)
- 1305
- Likes (Given)
- 5602
- Likes (Received)
- 11033
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
Good stuff! Be very strong and will fly right. Nice neat glass work.
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
-
VkingMike liked this post
-
01-10-2023, 02:39 PM #3Junior Member
- Join Date
- Sep 2021
- Location
- South Louisiana
- Posts
- 21
- Thanks (Given)
- 3
- Thanks (Received)
- 0
- Likes (Given)
- 3
- Likes (Received)
- 14
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Thanks! Hope she flys and is safe.
-
01-10-2023, 02:41 PM #4
-
rgsauger liked this post
-
01-10-2023, 02:59 PM #5
looking good, nice and clean glass work.
1973 Viper - sold
1978 Viking - sold
1995 XB02
-
01-10-2023, 03:02 PM #61973 Viper - sold
1978 Viking - sold
1995 XB02
-
01-10-2023, 03:09 PM #7Junior Member
- Join Date
- Sep 2021
- Location
- South Louisiana
- Posts
- 21
- Thanks (Given)
- 3
- Thanks (Received)
- 0
- Likes (Given)
- 3
- Likes (Received)
- 14
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Thanks fellas, debating weather i should put stringers in now then put the core on the outside of them or do the core first then bed the stringers in. I was worried without the stringers there the core may want to slide down some once i bed it in and put some wait on top of it.
-
01-10-2023, 03:17 PM #8Junior Member
- Join Date
- Sep 2021
- Location
- South Louisiana
- Posts
- 21
- Thanks (Given)
- 3
- Thanks (Received)
- 0
- Likes (Given)
- 3
- Likes (Received)
- 14
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
So for that area rj, i wetted out a piece of 1.5 oz on a flat table with clear wrap on it the. When that hardened i cut out pieces to fit in that gap and classed from both sides, then went from the back and tied in what i cut out in the wood with new wood bonding it to the transom and existing wood under there. Only thing i want to do is cut out another piece of 1/2 inch about 6 or 8 inches longer then the patch and laminate it over that
-
01-10-2023, 04:00 PM #9
It helps a lot connecting the cap stringers to the top corners of the transom. I would go stingers first as your not bagging the core down, it may slide like you said.
1973 Viper - sold
1978 Viking - sold
1995 XB02
-
01-10-2023, 07:00 PM #10
Nice!
Hydrostream dreamin
-
01-11-2023, 10:45 AM #11Junior Member
- Join Date
- Sep 2021
- Location
- South Louisiana
- Posts
- 21
- Thanks (Given)
- 3
- Thanks (Received)
- 0
- Likes (Given)
- 3
- Likes (Received)
- 14
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I was gunna mix up some resin and milled fibers into a paste to bed stringers in. Is there a better way to do it then that?
-
01-11-2023, 11:55 AM #121973 Viper - sold
1978 Viking - sold
1995 XB02
-
01-11-2023, 11:59 AM #13Junior Member
- Join Date
- Sep 2021
- Location
- South Louisiana
- Posts
- 21
- Thanks (Given)
- 3
- Thanks (Received)
- 0
- Likes (Given)
- 3
- Likes (Received)
- 14
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Sounds good yeah i have cabosil also
-
01-13-2023, 09:56 AM #14Screaming And Flying!
- Join Date
- Dec 2001
- Posts
- 9,502
- Thanks (Given)
- 23
- Thanks (Received)
- 271
- Likes (Given)
- 191
- Likes (Received)
- 1976
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Me thinks this guy likes his boat......... Nice job.
-
BrononC liked this post
-
01-13-2023, 12:23 PM #15
Project looks great. Those things are a blast to drive.
RockTeam Junk
No sparkling wiggles in here, only dump truck grinches.
"Screamin Heathen"
Similar Threads
-
1983 Vector
By scottmcbx in forum Fiberglass and Composites DiscussionReplies: 0Last Post: 01-23-2015, 12:35 AM -
1983 Vector pad
By scottmcbx in forum Technical DiscussionReplies: 18Last Post: 09-02-2014, 11:07 AM -
1983 Hydrostream Vector
By scottmcbx in forum Technical DiscussionReplies: 3Last Post: 09-02-2014, 10:56 AM -
1983 Vector I buffed on/ before and after
By zzzman in forum Fiberglass and Composites DiscussionReplies: 3Last Post: 04-29-2006, 04:31 PM