User Tag List
Thanks: 0
Likes: 0
Results 1 to 7 of 7
Thread: have any OMC high speed jets?
-
12-14-2022, 08:00 PM #1Member
- Join Date
- May 2013
- Location
- Michigan
- Posts
- 45
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 5
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
have any OMC high speed jets?
Hi all. I hope this is the best forum for this thread. I have two 1980s 2-stroke Evinrude V6's (1985 175hp and 1984 2.6 XP). I want to replace the main jets to increase the fuel a bit. I have determined the sizes I need and I'll need 6 of each to do some experimenting. Wondering if anyone has any new or good used jets. Willing to buy for fair prices. Below are the sizes I'm looking for (I think!).
175:
OMC p/n size
320661 61C
317607 62C
321559 63C
2.6:
OMC p/n size
328554 66C
317183 67C
328555 68C
James
-
12-14-2022, 08:28 PM #2
40 years ago I put them in a drill press and...
We have invented the world; WE see
-
12-14-2022, 08:44 PM #3Member
- Join Date
- May 2013
- Location
- Michigan
- Posts
- 45
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 5
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Good point. There’s a chance that’s what I might do, but I don’t have a drill press. Could drilling them free hand be any different? Some guys say there’re precision machined, finished, chamfered, and I know the micro bits you can buy in expensively are junk. Good micro bits are pricey. Then do you end up with the correct flow?? I sure don’t know.
-
12-14-2022, 09:23 PM #4
Always hated carbs
We have invented the world; WE see
-
12-16-2022, 05:13 PM #55000 RPM
- Join Date
- May 2004
- Location
- Eastern PA
- Posts
- 594
- Thanks (Given)
- 1
- Thanks (Received)
- 29
- Likes (Given)
- 0
- Likes (Received)
- 54
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I was able to find OMC (new old stock) from Sea Way Marine in Washington State but it’s been a while since I’ve dealt with them. Worth a phone call…
-
12-16-2022, 08:35 PM #6Member
- Join Date
- May 2013
- Location
- Michigan
- Posts
- 45
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 5
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Thanks! I will try them. I’ve heard of them, a local dealer referred me to them a while back on some other nla part.
-
12-17-2022, 08:19 AM #7
Similar Threads
-
Have You Checked Your High Speed Jets
By keith scotton in forum Technical DiscussionReplies: 100Last Post: 02-09-2021, 05:39 PM -
72D high speed jets for my 120 looper
By NWolf in forum Technical DiscussionReplies: 25Last Post: 04-10-2018, 07:22 PM -
Need Johnson 225 high speed jets, 72D, 74D
By Tightrig 12 in forum Parts WantedReplies: 0Last Post: 11-20-2017, 04:37 PM -
low, mid, and high speed jets
By strehl in forum Technical DiscussionReplies: 12Last Post: 06-05-2008, 07:36 PM