User Tag List
Thanks: 0
Results 1 to 5 of 5
Thread: 32x15.5 Mad Efi 4 Blade
-
10-04-2021, 02:56 PM #1Member
- Join Date
- Apr 2017
- Location
- key largo florida
- Posts
- 41
- Thanks (Given)
- 1
- Thanks (Received)
- 1
- Likes (Given)
- 2
- Likes (Received)
- 10
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
32x15.5 Mad Efi 4 Blade
32x15.5 Mad EFI 4 Blade
$800
305-587-3095Last edited by L&B; 10-18-2021 at 10:14 PM.
-
NAVISPEED1 liked this post
-
10-09-2021, 05:29 PM #2Supporting Member
- Join Date
- Apr 2003
- Location
- New Smyrna Beach, FL./LOTO
- Posts
- 6,637
- Thanks (Given)
- 606
- Thanks (Received)
- 920
- Likes (Given)
- 1698
- Likes (Received)
- 7133
- Mentioned
- 3 Post(s)
- Tagged
- 1 Thread(s)
Guys with the 21 skaters that are used to running the 32 pro-et....This is your modern day replacement (you will need to take some diameter out or run your motor higher to turn it up).
Joe
-
webbie73 liked this post
-
10-21-2021, 09:43 AM #3Supporting Member
- Join Date
- Apr 2003
- Location
- New Smyrna Beach, FL./LOTO
- Posts
- 6,637
- Thanks (Given)
- 606
- Thanks (Received)
- 920
- Likes (Given)
- 1698
- Likes (Received)
- 7133
- Mentioned
- 3 Post(s)
- Tagged
- 1 Thread(s)
Sold,
Thanks Julian-
Joe
-
10-26-2021, 10:18 AM #45000 RPM
- Join Date
- Sep 2012
- Location
- Florida
- Posts
- 440
- Thanks (Given)
- 2
- Thanks (Received)
- 15
- Likes (Given)
- 9
- Likes (Received)
- 84
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
So....got my attention here. I have been looking for a Pro ET that is unobtainium these days. I looked at this prop and saw that it was a 15.5 which is an inch over the ET. So are you saying to buy one of these in a 32 and get it cut down an inch? Or maybe can a 30 work just as well? Are these props available new? Are they a copy of the ET with a bigger diameter? This is for a 21 cat.
-
11-02-2021, 12:19 AM #5Supporting Member
- Join Date
- Apr 2003
- Location
- New Smyrna Beach, FL./LOTO
- Posts
- 6,637
- Thanks (Given)
- 606
- Thanks (Received)
- 920
- Likes (Given)
- 1698
- Likes (Received)
- 7133
- Mentioned
- 3 Post(s)
- Tagged
- 1 Thread(s)
They are not a copy of an ET but do have a very similar blade design. They are a thru hub Vs the Pro-et being an over hub, but they work very well like a Pro-et always has on on heavier hulls. The reason I said you would have to cut it down is simply due to horsepower restrictions "it takes some real torque to put a 15 1/2 dia. four blade into the 6K and up zone without bringing the motor up really high which then pulls blade surface out of the water and lets it rev".
-
NAVISPEED1 liked this post
Similar Threads
-
Cleaver Prop: 32x15 LH and Rh labbed
By steven_koenke in forum PropellersReplies: 6Last Post: 05-18-2020, 11:24 PM -
WANTED: RH bigshaft 32x15 Merc 3 blade cleaver or pair of 15x34 3 blade cleavers
By WILDMAN in forum Propellers WantedReplies: 0Last Post: 08-21-2017, 07:15 PM -
Lost a blade on my 3 blade Mercury Lightning ET and ......
By Stålproppen in forum Technical DiscussionReplies: 24Last Post: 07-20-2016, 06:48 PM -
Drag 4 32p, Hoss 4 blade 28p, mercury et 3 blade 32p
By Mercaholic86 in forum PropellersReplies: 22Last Post: 05-02-2016, 02:41 PM