User Tag List
Thanks: 0
Results 16 to 25 of 25
Thread: lower unit stuff
-
04-22-2021, 04:20 AM #16
Ive pulled my case to bits and are going through it.
Would it be typical to have a 43 44103-1 pinion matched with a 44 104/2 foreword gear ?
The pinion is cracked on the top side boss and both have a radial or perpendicular wear line about 5/16ths in from the large end of each tooth.
There are 2 cracks and one of them runs 1/16th down the side of the boss.
These wont be going back in.Last edited by NZ Sidewinder; 04-22-2021 at 04:34 AM.
-
04-22-2021, 06:26 AM #17
-
04-25-2021, 05:07 AM #18Junior Member
- Join Date
- Apr 2012
- Location
- Mobile, AL
- Posts
- 5
- Thanks (Given)
- 1
- Thanks (Received)
- 0
- Likes (Given)
- 3
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Hi Rock, Sam here, not sure i can help with identifying my prop shaft/lower unit, I'm a noob. But from what I have read... isn't a preload unit identified by having the pin sticking out of the top of the driveshaft? Problem is that its been over a year since I had it off and I just cant remember and i can't pull the lower right now to look. It's a 2:1 lower unit, stock 1994 2.0L Mariner 150 fishing motor s# 0B042790. Those were consumer motors so t's probably the weakest and cheapest of all available, LOL. Thank you, Sam
-
06-13-2021, 04:40 PM #19Junior Member
- Join Date
- Dec 2011
- Location
- S.C
- Posts
- 17
- Thanks (Given)
- 0
- Thanks (Received)
- 1
- Likes (Given)
- 0
- Likes (Received)
- 2
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Do you still have the xr6 2:1 gear set ?
-
06-13-2021, 07:46 PM #20
Yes I do.
RockTeam Junk
No sparkling wiggles in here, only dump truck grinches.
"Screamin Heathen"
-
06-14-2021, 09:00 PM #21Junior Member
- Join Date
- Dec 2011
- Location
- S.C
- Posts
- 17
- Thanks (Given)
- 0
- Thanks (Received)
- 1
- Likes (Given)
- 0
- Likes (Received)
- 2
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I will take that gear set and a propshaft
-
07-02-2021, 02:33 AM #22
Any 20in 2.5 drive shafts left with good water pump base seal area in good condition? Also if you have a pinion with 15 teeth on the gear side and 13 teeth on the inside and it looks good i will take that also. Thanks for looking. LMK.
-
08-07-2021, 02:50 PM #23Junior Member
- Join Date
- Jan 2012
- Location
- Kings Mountain NC
- Posts
- 13
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Do you have a set of the 44103, 44104, and 44105 gears left? I sent you a PM. Thanks
-
08-08-2021, 07:31 AM #24
Darknet I owe you an apology as I did not see this post. I will look today but don't think there were any drive shafts left. I'll check for the pinion. Sorry. Gmann I will check today.
RockTeam Junk
No sparkling wiggles in here, only dump truck grinches.
"Screamin Heathen"
-
08-09-2021, 10:38 AM #25
I do have the pinion and sent you a pm.
RockTeam Junk
No sparkling wiggles in here, only dump truck grinches.
"Screamin Heathen"
Similar Threads
-
Lower unit woes.... some of the stuff I here!!!
By Eagle One in forum Technical DiscussionReplies: 7Last Post: 04-21-2012, 03:17 PM -
3,0 lower unit versus 2,5 same stuff inside ?
By ae23 in forum Technical DiscussionReplies: 1Last Post: 02-24-2009, 05:22 PM