User Tag List
Thanks: 0
Results 1 to 10 of 10
-
12-04-2020, 12:50 PM #1
MERC PROMAX 225 water tubbing dump
Hi,
I live in “hot” weather and when I start my engines water comes out hot to my hand in low rpms. I have changed the system and now it is better. When running hi rpm I see not
much water coming out but psi and temp are ok.
Later I installed a 3/8 barb with reduction to 1/4 but Not sure if this new water dump design in general is wrong or OK.
can someone please help here.
regards,
Last edited by rarias; 12-04-2020 at 10:04 PM.
-
12-04-2020, 11:58 PM #2
Just be careful experimenting with cooling , do you have a temp guage
-
12-05-2020, 11:15 AM #3
Yes, temp and psi
-
12-05-2020, 01:55 PM #4Screaming And Flying!
- Join Date
- Jul 2004
- Location
- Connecticut
- Posts
- 6,010
- Thanks (Given)
- 465
- Thanks (Received)
- 168
- Likes (Given)
- 911
- Likes (Received)
- 951
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
-
12-05-2020, 06:05 PM #5
you don't need that piece between tha dumps from t-stats.. your t-stats control how much water discharges... unless ya changed to a one piece i'd leave it completely stock.. T-stats, poppet, discharge.. if it runs hot and /or pressure ain't right stock ya gotta problem somewhere........ jmo
looks cool though.....................
-
TEXAS20225 liked this post
-
12-06-2020, 09:12 PM #6
Hi Greg,
its 1998 fully stock.
-
12-06-2020, 09:17 PM #7
tlwjkw: The piece between dumps you mean the hose connecting both dump tubing??? Or the barb with reduction?
thanks,
-
12-07-2020, 03:03 AM #8
tha parts circled or tha barbed thingies in tha ends of tha discharge hoses don't contribute in any way to tha coolin' system.. like i mentioned earlier.. unless you go to tha "one piece" adapter plate (which i don't thing you did) there is absolutely no gain with modifying tha stock coolin' system stuff.. jmo.
there's tons of mercs in your same waters that run stock coolin' junk with no problems soooooooooooooooo... does your "over temp" buzzer go off?
assuming all three pictures are same motor, did you do anything to tha motor "after" you got it? (other than tha discharge stuff)Last edited by tlwjkw; 12-07-2020 at 03:22 AM.
-
12-07-2020, 10:26 AM #9
Got it , will remove reduction and the circled tubbing asap. The only change done to discharge was from pic1 to pic 2.
Everything else is stock.
-
12-07-2020, 10:53 AM #10
if ya like havin' two discharge hose's jus drop one from each t-stat housin'................
Similar Threads
-
Mercury Tech: Promax 225 fresh water dump ???
By rarias in forum Technical DiscussionReplies: 2Last Post: 07-02-2020, 12:23 AM -
Stainless water dump
By aggiestckl in forum Misc. Parts and AccessoriesReplies: 0Last Post: 01-26-2018, 10:44 AM -
Engine water dump.
By Magoo36 in forum Jet Boats, V-Drives and Stern DrivesReplies: 1Last Post: 08-09-2011, 11:25 AM -
Dump water
By racer in forum General Boating DiscussionReplies: 7Last Post: 07-01-2008, 07:57 AM -
Merc water tube dump question??
By gambler183gt in forum Technical DiscussionReplies: 4Last Post: 05-23-2006, 03:23 PM