User Tag List
Likes: 0
Results 1 to 7 of 7
Thread: Threaded tilt tube split collar
-
11-30-2020, 05:59 PM #16000 RPM
- Join Date
- Feb 2011
- Location
- HUDSON, FLORIDA
- Posts
- 1,528
- Thanks (Given)
- 431
- Thanks (Received)
- 64
- Likes (Given)
- 434
- Likes (Received)
- 451
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Threaded tilt tube split collar
i am missing the collar used on seastar ram assembly, used in starboard end of tilt tube to take up slack, its a thick piece uses an allen to lock. cant seem to find this piece. can i stack ss washers instead, getting the same result?
-
11-30-2020, 06:34 PM #2
I think I bottomed mine out and made new spacers for both ends rather than using the nut to take up the slack.
Is it this one (mine is different if I remember right): https://www.ebay.com/i/203194783903?...caAj3EEALw_wcB
-
KIRCHNER thanked for this post
-
11-30-2020, 06:49 PM #3
Seems like mine was not split and had a pointed set screw through the side that jammed into the threaded portion of the rod? Boat's far away in storage now, or I would get a photo.
-
11-30-2020, 06:49 PM #4The Historic Photo Master
- Join Date
- Jan 2004
- Location
- Florida
- Posts
- 37,831
- Thanks (Given)
- 64
- Thanks (Received)
- 1667
- Likes (Given)
- 337
- Likes (Received)
- 19215
- Mentioned
- 3 Post(s)
- Tagged
- 0 Thread(s)
...seastar # hp6034... available all over the interweb...
-
11-30-2020, 07:00 PM #56000 RPM
- Join Date
- Feb 2011
- Location
- HUDSON, FLORIDA
- Posts
- 1,528
- Thanks (Given)
- 431
- Thanks (Received)
- 64
- Likes (Given)
- 434
- Likes (Received)
- 451
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
A while ago i cut some 1/2 starboard, with a hole saw, ss washer each side, 0 slack.. that pic is it, but il keep my 30$ for now.. gonna restore the old skater18. going to paint it to match the 2.4 220 15'' battleship gray/ orange accents mariner-mag colors. rub rail, jplate, seats, now the fl. heat is over.
-
11-30-2020, 07:27 PM #6The Historic Photo Master
- Join Date
- Jan 2004
- Location
- Florida
- Posts
- 37,831
- Thanks (Given)
- 64
- Thanks (Received)
- 1667
- Likes (Given)
- 337
- Likes (Received)
- 19215
- Mentioned
- 3 Post(s)
- Tagged
- 0 Thread(s)
...we all thought you needed that piece & couldn't find one...
-
11-30-2020, 09:12 PM #76000 RPM
- Join Date
- Feb 2011
- Location
- HUDSON, FLORIDA
- Posts
- 1,528
- Thanks (Given)
- 431
- Thanks (Received)
- 64
- Likes (Given)
- 434
- Likes (Received)
- 451
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Similar Threads
-
Tilt Tube and Swivel Tube Bushings?
By 2.5-21 in forum Technical DiscussionReplies: 1Last Post: 09-02-2016, 08:17 PM -
Tilt Tube ?
By gaineso in forum Technical DiscussionReplies: 1Last Post: 09-08-2003, 02:05 PM