User Tag List

Results 1 to 4 of 4
  1. #1
    Join Date
    Apr 2001
    Location
    Western Pennsylvania
    Posts
    3,882
    Thanks (Given)
    48
    Thanks (Received)
    92
    Likes (Given)
    184
    Likes (Received)
    378
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    50hp water peeing issue...

    impeller was replaced by shop and during water test on pontoon I'm purchasing stopped peeing after about 20 minutes of running. shop stated impeller was melted and vanes went into power head. Yep, I purchased since shop quoted $2500+ to dismantle powerhead. I'm going to purchase service manual but until it arrives what is located under this cover? Is this wear water from WP goes into powerhead. Also p-hose is attached to this area.
    Attached Thumbnails Attached Thumbnails IMG_4096.jpg   61799079519__D87E7458-70A6-425D-8FB3-88BB44ACE4B4.jpg  
    Checkmate 2002 Convincor 270 496 MAG-HO

    2003 Cougar 22MTR w/300xs SOLD
    90 21Skater w/300xs - sold
    98 STV Euroski w/280 - sold


    2006 Trailblazer SS 6.0l 395hp

  2. #2
    Join Date
    Oct 2010
    Location
    Harrisburg,Pa
    Posts
    2,053
    Thanks (Given)
    2
    Thanks (Received)
    45
    Likes (Given)
    20
    Likes (Received)
    183
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Check the place where the pee hose hooks to the motor block,take the hose off there and see if it will pee from that fitting. If not probe it with a piece of wire. They clog all the time.

  3. Likes Capt.Insane-o liked this post
  4. #3
    Join Date
    Apr 2001
    Location
    Western Pennsylvania
    Posts
    3,882
    Thanks (Given)
    48
    Thanks (Received)
    92
    Likes (Given)
    184
    Likes (Received)
    378
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Got back to basics and U checked the work that the marine shop rookie did. didn't clean all the old impeller out from the intake side below the plate. Output to power head wasw plugged at tube. connected hose to pipe and engine peed fine. cleaned it out and put 4-5 hours over the weekend.
    Attached Thumbnails Attached Thumbnails IMG_4115.jpg   IMG_4101.jpg   IMG_4100.jpg  
    Checkmate 2002 Convincor 270 496 MAG-HO

    2003 Cougar 22MTR w/300xs SOLD
    90 21Skater w/300xs - sold
    98 STV Euroski w/280 - sold


    2006 Trailblazer SS 6.0l 395hp

  5. #4
    Join Date
    Oct 2010
    Location
    Harrisburg,Pa
    Posts
    2,053
    Thanks (Given)
    2
    Thanks (Received)
    45
    Likes (Given)
    20
    Likes (Received)
    183
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Backyard mechanic. Hey Euroski how are you doing I met you at Raystown I have the 23 Eliminator Daytona with twin 2.6 Evinrudes a few years back. And to answer your original question that cover is the water jacket cover for the exhaust housing and no that's not where the water comes up it comes up and in on the bottom of the power head
    Last edited by perfmarine1; 08-15-2020 at 11:49 AM.

Similar Threads

  1. Yamaha Tech: Yamaha 50hp over heat issue...
    By Euroski in forum Technical Discussion
    Replies: 4
    Last Post: 08-06-2020, 01:11 PM
  2. 300x not peeing
    By HIMAGAIN in forum Technical Discussion
    Replies: 4
    Last Post: 06-08-2016, 01:27 PM
  3. Yamaha 50hp crankshaft issue
    By fofiveoh in forum Technical Discussion
    Replies: 3
    Last Post: 04-29-2015, 01:15 PM
  4. Yamaha 50hp wiring issue
    By riverrat321 in forum Technical Discussion
    Replies: 2
    Last Post: 12-27-2014, 11:51 PM
  5. No water peeing at idle, wot only 8lbs
    By RUNWME in forum Technical Discussion
    Replies: 10
    Last Post: 07-08-2003, 02:07 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Aeromarine Research