User Tag List
Thanks: 0
Likes: 0
Results 1 to 7 of 7
Thread: Lwp in torque master
-
01-20-2020, 09:15 AM #1Member
- Join Date
- Dec 2019
- Location
- Denmark
- Posts
- 33
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Lwp in torque master
Hi
can anyone tell me we’re to drill the hole in gear case? I have a problem if the intake has to be as shown in the picture cause I get to close to the oil screw. But if I drill were the screwdriver is pointing I get close to were the housing/packing is and I won’t get the same water chamber and I’m not sure if this is okay?
hope it makes sense
-
01-20-2020, 10:59 AM #25000 RPM
- Join Date
- Mar 2004
- Location
- vonore tn.
- Posts
- 225
- Thanks (Given)
- 0
- Thanks (Received)
- 21
- Likes (Given)
- 4
- Likes (Received)
- 28
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
From what it looks like, you are wanting to install the transfer hose. From a LWP nose cone, to the LU hsg. That is the correct place.
-
01-20-2020, 12:10 PM #3Member
- Join Date
- Dec 2019
- Location
- Denmark
- Posts
- 33
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Yes the hose from a transom mounted intake. But I can’t drill the hole as shown on the picture (snatched fro the internet) because of the oil screw. Therefore I want to drill it we’re my screwdriver is pointing but then I get the hole much closer to the housing/gasket. Is that okay?
-
01-20-2020, 12:17 PM #4Screaming And Flying!
- Join Date
- Jul 2002
- Location
- FT WORTH, TEXAS
- Posts
- 8,031
- Thanks (Given)
- 9
- Thanks (Received)
- 146
- Likes (Given)
- 313
- Likes (Received)
- 503
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
3.0 gear case lower fin is cut off to accommodate 1/2 pipe elbow if you drill it that high you ill be out of material to thread for your fittings!!! 3.0 has to have two hose's to cool just my .02
-
01-20-2020, 12:23 PM #5Member
- Join Date
- Dec 2019
- Location
- Denmark
- Posts
- 33
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
01-21-2020, 04:46 PM #6Member
- Join Date
- Dec 2019
- Location
- Denmark
- Posts
- 33
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Has anyone tried cutting this piece of ??
-
01-22-2020, 02:51 PM #75000 RPM
- Join Date
- Mar 2004
- Location
- vonore tn.
- Posts
- 225
- Thanks (Given)
- 0
- Thanks (Received)
- 21
- Likes (Given)
- 4
- Likes (Received)
- 28
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Yes BOB,s cuts off front of spray plate, to make room for hose & fittings.
Similar Threads
-
Sport master vs torque master
By Ttl in forum Props, Setup, and RiggingReplies: 11Last Post: 01-13-2020, 06:17 PM -
torque master/sport master prop shaft (not fat shaft)
By heather5520 in forum Posting Questions and SuggestionsReplies: 0Last Post: 07-29-2011, 08:34 AM -
1:75 Sport Master Gears in a Torque Master.
By twig in forum Technical DiscussionReplies: 3Last Post: 06-13-2008, 08:43 AM -
Sports master vs Torque master
By Patmerc in forum Technical DiscussionReplies: 8Last Post: 06-02-2008, 07:36 PM