User Tag List

Thanks Thanks:  0
Likes Likes:  0
Results 1 to 7 of 7
  1. #1
    Join Date
    Sep 2007
    Location
    Pensacola FL
    Posts
    884
    Thanks (Given)
    2
    Thanks (Received)
    20
    Likes (Given)
    7
    Likes (Received)
    106
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Mercury Gear Set

    Looking for a clean undamaged complete set (fwd pinion rev) of merc inline 6 straight tooth 2:1 gears. Thanks alot
    Last edited by tcrabtree; 10-30-2019 at 03:21 PM.

  2. #2
    Join Date
    Dec 2001
    Posts
    9,503
    Thanks (Given)
    23
    Thanks (Received)
    270
    Likes (Given)
    191
    Likes (Received)
    1975
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    how about a whole lower unit?.... what year ya working on?......

  3. #3
    Join Date
    Sep 2007
    Location
    Pensacola FL
    Posts
    884
    Thanks (Given)
    2
    Thanks (Received)
    20
    Likes (Given)
    7
    Likes (Received)
    106
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    I just need the gears bud. Dont have much use for the entire case. Thanks for the offer sir

  4. #4
    Join Date
    Dec 2001
    Posts
    9,503
    Thanks (Given)
    23
    Thanks (Received)
    270
    Likes (Given)
    191
    Likes (Received)
    1975
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    There are 2 types of pinion splines..... which do you need?

  5. #5
    Join Date
    Sep 2007
    Location
    Pensacola FL
    Posts
    884
    Thanks (Given)
    2
    Thanks (Received)
    20
    Likes (Given)
    7
    Likes (Received)
    106
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Pm sent

  6. #6
    Join Date
    Dec 2001
    Posts
    9,503
    Thanks (Given)
    23
    Thanks (Received)
    270
    Likes (Given)
    191
    Likes (Received)
    1975
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    I didn't get a PM......just the first one......looking at L6 shafts and gears, the early shaft had 6 splines.... the later ones had 17 splines....V6 pre/load has 11 splines and a bigger gear/tapper..... The 17 spline has a cut above the splines that would be a week point.....If you want a better D/S the latter 3 and 4 cly loopers have no week point above the splines.You would have to have it cut to work.....All seem to have the same lower bearing out side dia.......

  7. #7
    Join Date
    Sep 2007
    Location
    Pensacola FL
    Posts
    884
    Thanks (Given)
    2
    Thanks (Received)
    20
    Likes (Given)
    7
    Likes (Received)
    106
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Mr dave you are correct, the older models used a much smaller pinion area on the drive shaft. Im looking for the later model that has the larger pinion. The Pinion gear im looking for will have 17 splines on the bottom of drive shaft profile. Thank you sir
    Last edited by tcrabtree; 11-07-2019 at 08:59 PM.

Similar Threads

  1. mercury 1.87 gear set
    By Cal 47 in forum Lower Units
    Replies: 7
    Last Post: 04-07-2015, 05:47 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Aeromarine Research