User Tag List
Results 106 to 113 of 113
Thread: 200 Black Max Low Water Pressure
-
11-15-2019, 11:44 AM #1065000 RPM
- Join Date
- Feb 2009
- Location
- Dunnellon, Fl. / Cincinnati, Oh
- Posts
- 419
- Thanks (Given)
- 62
- Thanks (Received)
- 28
- Likes (Given)
- 136
- Likes (Received)
- 162
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Might be my eyes, but I don't see any water diverters in there.
Maybe you pulled them out?
Hate to be a pest, but could you snap pics of both seperate sides of motor that includes all 3 holes with water passages?
Had a overheat problem on a motor kinda recently that turned out to be diverters, after I had replaced stats, poppets, grommets, pump and housing, water jacket gaskets, then finally head gaskets, where I found distorted diverters in the block passages.
Thank you, just curious.
-
11-15-2019, 11:53 AM #107
Sure , at work will when I get home. Here is where my amateur status comes into play on outboard engines. What do the diverters look like? I dont think there were any extra pieces.
Respect no wake zones!!! Evinrude guys need a place to race too.
-
11-15-2019, 12:23 PM #1085000 RPM
- Join Date
- Feb 2009
- Location
- Dunnellon, Fl. / Cincinnati, Oh
- Posts
- 419
- Thanks (Given)
- 62
- Thanks (Received)
- 28
- Likes (Given)
- 136
- Likes (Received)
- 162
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Look like pieces of fuel line, inserted between cylinder and water jacket.Here's what mine looked like (distorted), and here's what I replaced it with. (Fuel line). They direct (divert) water to flow around cylinders to cool properly.In my kooky sideways pic, you can see the diverter in the middle, between cylinders, and also another one at the bottom of block, uh, to the right side of the one in the middle.
Last edited by rochelle howell; 11-15-2019 at 12:30 PM.
-
TNRoostertail liked this post
-
11-15-2019, 02:42 PM #109
"production" 2.0's, 2.4's, 2.5's dont have diverters.....
-
TNRoostertail thanked for this postCapt.Insane-o liked this post
-
11-15-2019, 05:15 PM #1105000 RPM
- Join Date
- Feb 2009
- Location
- Dunnellon, Fl. / Cincinnati, Oh
- Posts
- 419
- Thanks (Given)
- 62
- Thanks (Received)
- 28
- Likes (Given)
- 136
- Likes (Received)
- 162
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
So all those pics of 2.4 merc with diverters in block are "modified" cooling systems or race motors?
My bad.
Good to know, thank you!
-
11-15-2019, 05:21 PM #111
some add 'em to their stuff 'cause it can be beneficial but, yeah only came in ha hi perf blocks...….
-
TNRoostertail thanked for this post
-
11-15-2019, 09:24 PM #112
When does it start to be beneficial Tommy? Over 8k? Can they be run on any cooling system?
-
11-15-2019, 09:43 PM #1136000 RPM
- Join Date
- Feb 2014
- Location
- Missouri
- Posts
- 1,212
- Thanks (Given)
- 2
- Thanks (Received)
- 66
- Likes (Given)
- 12
- Likes (Received)
- 83
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Looks like jets in backwards port and starboard, but not lean enough to be the heat problem.
The first piston pic where it’s busted up is probably causing silent knock (knock condition or ping you can’t hear) that will cause excessive heat.
Discoloring looks like scuffing, and is that oil or is the chrome cracked in that one pick. That will also cause excessive heat.
But since it it hasn’t been done ohm test the temp sensors to confirm their not bad. Not an pressing concern since you found physical damage, but might as well hit them up and take care of if needed while doing the rest.
Similar Threads
-
high water pressure problem on a black max
By mouse4x4 in forum Technical DiscussionReplies: 50Last Post: 05-16-2013, 09:41 PM -
Mercury Tech: what would be good water pressure for an 88 200 black max
By concord 1 in forum Technical DiscussionReplies: 6Last Post: 07-09-2009, 08:32 AM -
Black Max XR-2 150 / No water pressure to gauge!
By Rush in forum Technical DiscussionReplies: 16Last Post: 02-06-2005, 08:18 PM