User Tag List
Thanks: 0
Results 1 to 15 of 18
-
08-18-2019, 05:10 PM #1
2019 400R will not trim up under speed....
It's on a poontoon and it used to trim up as high as needed. I feel it must be a limiter/setting? Even at 1/2 throttle it will only trim up about 60% but if you you are idling it will trim all the way up? Any idea's?
Thank's2011 DCB F26
2017 300 XS DBR
-
08-19-2019, 06:54 AM #2
Vesselview(smartcraft) setting. It happened to me after Mercury screwed with it at the dealer. Would only go just above neutral trim. I changed setting in Vesselview
2005 APR FORMULA 2 ROOKIE OF THE YEAR
-
08-19-2019, 08:43 AM #3
-
08-19-2019, 08:48 AM #4
Check and make sure active trim is either disabled or settings are adjusted for your speeds.
Mark
-
08-19-2019, 08:57 AM #55000 RPM
- Join Date
- Mar 2017
- Location
- Miami, FL
- Posts
- 358
- Thanks (Given)
- 0
- Thanks (Received)
- 10
- Likes (Given)
- 1
- Likes (Received)
- 47
- Mentioned
- 1 Post(s)
- Tagged
- 1 Thread(s)
One of my verados stopped trimming up altogether when on plane. Test it by unplugging the trim sending unit. It is located at the back of the motor by the coils. The sending unit is the little rectangle thing that sticks out under the flush port on the port side of the motor.
In our case, unplugging the sending unit allowed it to trim again, so we replaced the sending unit and it all works well now
-
rochelle howell liked this post
-
08-19-2019, 10:01 AM #6
-
08-19-2019, 10:02 AM #7
-
08-19-2019, 08:46 PM #8
My boat setup does not have the active trim module installed it say. And I can't find any settings that would limit trim just calibration of the trim % that is displayed. When you found a setting was it like a limit for trim or?
Thank's2011 DCB F26
2017 300 XS DBR
-
08-26-2019, 11:00 AM #9
Update
No setting is the problem dealer hooked up there master computer and reset all trim stuff. Still no trim under power. They ordered a new trim sensor....... will update after installation.
Thank's2011 DCB F26
2017 300 XS DBR
-
08-31-2019, 07:04 AM #10
Well put a new trim sensor on it, when I took it off water was in the little pocket where the sensor mounts and the sensor was wet. Installed new sensor 99% sure problem was fixed seeing the trim sensor was wett! But after putting boat in water no good same thing. Trim works 100% perfect until you get up on plan and past line 50 throttle it will not trim up past like 55% now.
Help guy's!!!! Where to look next? Does engine need programming after sensor installation? Sounds dumb but I did kill the batteries last night have not done that all year. Will see what it does today.
Thank's Skydog2011 DCB F26
2017 300 XS DBR
-
08-31-2019, 10:57 AM #11
Trim fluid level?
Burned trim motor?
-
08-31-2019, 03:22 PM #12
Why isn’t the dealer fixing it?
Mark
-
Whaaaaat, Forkin' Crazy liked this post
-
08-31-2019, 08:40 PM #13Screaming And Flying!
- Join Date
- Dec 2001
- Posts
- 9,502
- Thanks (Given)
- 23
- Thanks (Received)
- 269
- Likes (Given)
- 191
- Likes (Received)
- 1975
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
If it is a 3 ram.... it could be the main relief screw......Bad o rings/ broken tip that holds the last O ring......If single ram?????The hoses switched......the rev has a press relief that lets go if ya hit some thing.....at least the old ones.
-
08-31-2019, 08:53 PM #14
-
09-01-2019, 11:49 AM #156000 RPM
- Join Date
- Jul 2011
- Location
- Gloucester, VA
- Posts
- 1,311
- Thanks (Given)
- 19
- Thanks (Received)
- 90
- Likes (Given)
- 180
- Likes (Received)
- 342
- Mentioned
- 2 Post(s)
- Tagged
- 0 Thread(s)
Sounds like someone has the limits messed up.
The dealer needs to hook up G3 and look at the counts.
If you have smartcraft you can reset it yourself at home
Similar Threads
-
400R vs. 400R Carbon Edition
By whytey in forum General Boating DiscussionReplies: 13Last Post: 08-21-2020, 04:40 PM -
2019 25' ocean express speed series
By FSTBTS in forum Hulls larger than 20'Replies: 7Last Post: 04-06-2019, 06:10 PM -
Mercury Tech: speed up trim
By new in forum Technical DiscussionReplies: 10Last Post: 02-12-2018, 10:57 AM -
Trim speed and jack plate speed
By Krazymaan in forum General Boating DiscussionReplies: 9Last Post: 06-04-2017, 06:40 AM -
DCB M29 vs Eliminator 28 speedster 400r verado trim level
By conmax in forum General Boating DiscussionReplies: 26Last Post: 10-05-2016, 09:05 AM