User Tag List
Results 1 to 15 of 39
-
08-05-2019, 10:11 PM #1Member
- Join Date
- Oct 2017
- Location
- columbus,ohio
- Posts
- 39
- Thanks (Given)
- 5
- Thanks (Received)
- 0
- Likes (Given)
- 2
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
08-09-2019, 12:16 PM #2Member
- Join Date
- Oct 2017
- Location
- columbus,ohio
- Posts
- 39
- Thanks (Given)
- 5
- Thanks (Received)
- 0
- Likes (Given)
- 2
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Well I bought the gasket kit8107492, the float 810738 and the valve seal kit 811690
My question is can I use the old bowl needle clip since it did not come with the 811690 kit?
Why would the sell a kit that has the seat, the gasket and the needle but no clip??? Unbelievable...
I cannot even find it on mercurys website catalog. Thanks for any insight. Guess Im not going to the lake
-
08-09-2019, 02:55 PM #3
tha "old" clip should be fine long as ya don't bend it outta shape some how.... don't remember ever seein' a new one included or separate anywhere..
normally a can of brake-kleen, hot soapy water, "all new" gaskets and a compressor is all that's needed....Last edited by tlwjkw; 08-09-2019 at 02:58 PM.
-
kramerpage thanked for this post
-
08-09-2019, 04:15 PM #4Screaming And Flying!
- Join Date
- Dec 2001
- Posts
- 9,502
- Thanks (Given)
- 23
- Thanks (Received)
- 271
- Likes (Given)
- 191
- Likes (Received)
- 1976
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Just for reff... them are bigg bore....150 carbs.....might be a miss lable....135s were way smaller.....
-
08-10-2019, 04:52 PM #5Member
- Join Date
- Oct 2017
- Location
- columbus,ohio
- Posts
- 39
- Thanks (Given)
- 5
- Thanks (Received)
- 0
- Likes (Given)
- 2
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I went ahead and used the old ones. Could not find them anywhere on the south shore of lake erie
Rebuild went well. Soaked bodies and parts in a gallon of carb medic then dawn and hot water and then warm water. Installed this morning and it runs smooth and responsive. Got her up to 48 mph. Going to do the other 3 carbs this week for the other motor. Thanks for your replies.
-
08-10-2019, 04:57 PM #6Member
- Join Date
- Oct 2017
- Location
- columbus,ohio
- Posts
- 39
- Thanks (Given)
- 5
- Thanks (Received)
- 0
- Likes (Given)
- 2
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
08-10-2019, 05:26 PM #7
84,s 1.315 Venturi , 34-310 throttle blades , I just installed them in my 245 carbs had 34-309 could never tune the carbs not enough air ,with 34-310 The fuel mixture screws are active. Those carbs you have will make the 135 closer to 150 hp
Last edited by eli; 08-10-2019 at 05:31 PM.
-
08-10-2019, 08:57 PM #8Member
- Join Date
- Oct 2017
- Location
- columbus,ohio
- Posts
- 39
- Thanks (Given)
- 5
- Thanks (Received)
- 0
- Likes (Given)
- 2
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Yes 34-310 butterflies on them. Fuel mixture screws??
I only know about the idle screws. Please enlighten me. On the 245s?
-
08-10-2019, 09:20 PM #95000 RPM
- Join Date
- Feb 2009
- Location
- Dunnellon, Fl. / Cincinnati, Oh
- Posts
- 419
- Thanks (Given)
- 62
- Thanks (Received)
- 28
- Likes (Given)
- 136
- Likes (Received)
- 162
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Wulffe Marine, Mentor, Ohio.
On the south shore of Lake Erie.
Glm, sierra, cdi electronics.
I used them for my carb kits and fuel pump kit for my older 175 merc.
Friendly, fast, and very reasonable.
Would use them again without hesitation, had my "stuff" to me in a couple days!
They're on eBay and have a website with their address.Last edited by rochelle howell; 08-10-2019 at 11:20 PM.
-
08-11-2019, 02:38 PM #10Member
- Join Date
- Oct 2017
- Location
- columbus,ohio
- Posts
- 39
- Thanks (Given)
- 5
- Thanks (Received)
- 0
- Likes (Given)
- 2
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
08-11-2019, 08:10 PM #115000 RPM
- Join Date
- Feb 2009
- Location
- Dunnellon, Fl. / Cincinnati, Oh
- Posts
- 419
- Thanks (Given)
- 62
- Thanks (Received)
- 28
- Likes (Given)
- 136
- Likes (Received)
- 162
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Ouch!
-
08-11-2019, 08:14 PM #12
Fuel mixture screws on the sides are worth 3 jet sizes out 2 turns from 0
-
08-11-2019, 09:43 PM #13Member
- Join Date
- Oct 2017
- Location
- columbus,ohio
- Posts
- 39
- Thanks (Given)
- 5
- Thanks (Received)
- 0
- Likes (Given)
- 2
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
08-11-2019, 09:47 PM #14Member
- Join Date
- Oct 2017
- Location
- columbus,ohio
- Posts
- 39
- Thanks (Given)
- 5
- Thanks (Received)
- 0
- Likes (Given)
- 2
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
08-11-2019, 10:23 PM #155000 RPM
- Join Date
- Feb 2009
- Location
- Dunnellon, Fl. / Cincinnati, Oh
- Posts
- 419
- Thanks (Given)
- 62
- Thanks (Received)
- 28
- Likes (Given)
- 136
- Likes (Received)
- 162
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Similar Threads
-
lean sneeze....where to pay special attention when rebuilding and cleaning carb
By cocacola in forum Technical DiscussionReplies: 7Last Post: 09-06-2016, 07:15 PM -
OMC Tech: newer v4 crossflow carbs, the bead plug and carb cleaning?
By pcrussell50 in forum Technical DiscussionReplies: 9Last Post: 07-27-2014, 11:35 AM -
Cleaning vinyl with Lacquer Thinner - Last Resort type cleaning
By Mr. Demeanor in forum General Boating DiscussionReplies: 18Last Post: 03-22-2013, 04:18 PM -
Professional carb cleaning & rebuilding
By Mark75H in forum Paying Advertiser Sales and New ProductsReplies: 3Last Post: 09-26-2010, 07:35 PM -
Carb Cleaning With Air Hose
By bgsgbgcg in forum Technical DiscussionReplies: 2Last Post: 04-22-2008, 10:22 AM