User Tag List
Thanks: 0
Results 1 to 15 of 32
-
07-18-2019, 07:08 PM #15000 RPM
- Join Date
- Jun 2001
- Posts
- 211
- Thanks (Given)
- 1
- Thanks (Received)
- 1
- Likes (Given)
- 0
- Likes (Received)
- 5
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Need Help, Flip my STV and it is laying up side down in the river
Just came from the river where I hit a roller coming down I stuff the one of the forks ! Boat ended up upside down ? Still upside down? Any one know and easy way to get it turned over so I can drain it slowly on the trailer and get the water out of the motor?
-
07-18-2019, 07:22 PM #2
So is it tied to bank upside down or sumthin? Hope u r ok
-
07-18-2019, 08:04 PM #3
How deep is the water where the boat is now?
18 Talon/2.4 carb SOLD
26 Deck Boat/250 Merc
-
07-18-2019, 08:33 PM #4
Call me I can probably help but getting different info where you are located 715-977-0185 Jerry
-
07-18-2019, 08:58 PM #5Supporting Member
- Join Date
- Apr 2003
- Location
- New Smyrna Beach, FL./LOTO
- Posts
- 6,644
- Thanks (Given)
- 606
- Thanks (Received)
- 923
- Likes (Given)
- 1698
- Likes (Received)
- 7148
- Mentioned
- 3 Post(s)
- Tagged
- 1 Thread(s)
Where are you located? I am sure we can group put together for a flip and recover mission. Nobody was injured l assume?
Joe
-
07-18-2019, 09:03 PM #6
-
07-18-2019, 09:51 PM #7
He is up in crivits Wisconsin. I contacted a friend with cabin close by. He is not there but trying to contact some friends in area. Anybody else in area?
-
07-19-2019, 07:15 AM #8Screaming And Flying!
- Join Date
- Sep 2001
- Location
- shreveport,la
- Posts
- 5,706
- Thanks (Given)
- 6
- Thanks (Received)
- 118
- Likes (Given)
- 85
- Likes (Received)
- 773
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I’d highly recommend you tear the engine down as soon as you get it out. If it can’t happen immediately then try to get all the water out and get it fired but I’d still fog it and tear it down. It’s very difficult to get all the water out unless it comes completely apart. It’ll collect in the bottom cap and eventually ruin a crank
Erik Kiser
-
07-19-2019, 09:16 AM #9
Sure hope he is ok but not responding when so many tryin to help sucks
-
07-19-2019, 10:46 AM #10
They are ok sounded like it was him and son in boat. I'm sure a little stiff today.
-
07-19-2019, 11:00 AM #11
-
Mugs914 liked this post
-
07-19-2019, 11:10 AM #12Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,753
- Thanks (Given)
- 381
- Thanks (Received)
- 1305
- Likes (Given)
- 5602
- Likes (Received)
- 11033
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
Maybe lesson learned......
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
-
07-19-2019, 05:32 PM #13Banned
- Join Date
- Jan 2015
- Location
- Wisconsin
- Posts
- 2,331
- Thanks (Given)
- 458
- Thanks (Received)
- 343
- Likes (Given)
- 6429
- Likes (Received)
- 5147
- Mentioned
- 4 Post(s)
- Tagged
- 0 Thread(s)
I am 25 miles away and can get a few people to help. Pm is best.
-
07-19-2019, 05:34 PM #14Banned
- Join Date
- Jan 2015
- Location
- Wisconsin
- Posts
- 2,331
- Thanks (Given)
- 458
- Thanks (Received)
- 343
- Likes (Given)
- 6429
- Likes (Received)
- 5147
- Mentioned
- 4 Post(s)
- Tagged
- 0 Thread(s)
High falls flowage?
-
07-19-2019, 06:03 PM #15Banned
- Join Date
- Jan 2015
- Location
- Wisconsin
- Posts
- 2,331
- Thanks (Given)
- 458
- Thanks (Received)
- 343
- Likes (Given)
- 6429
- Likes (Received)
- 5147
- Mentioned
- 4 Post(s)
- Tagged
- 0 Thread(s)
Similar Threads
-
Need to tansport a fully dressed 2.5 lt PH- can I safely do it laying on it's side?
By CircleHook in forum Technical DiscussionReplies: 1Last Post: 05-11-2016, 04:43 PM -
Flip This House
By INXS in forum The Scream And Fly LoungeReplies: 28Last Post: 09-08-2007, 01:44 PM -
Anyone have one of these laying around?
By LakeRacer99 in forum Outboard and Racing HistoryReplies: 3Last Post: 03-02-2003, 11:39 AM