User Tag List
Thanks: 0
Likes: 0
Results 1 to 5 of 5
Thread: omc tech over oiling
-
06-24-2019, 12:49 PM #15000 RPM
- Join Date
- Jun 2009
- Location
- central minnesota
- Posts
- 770
- Thanks (Given)
- 6
- Thanks (Received)
- 30
- Likes (Given)
- 5
- Likes (Received)
- 24
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
omc tech over oiling
2000 150 Johnson 60* eagle motor,just replaced carb bowls/and carb kits-also replaced vro pump and plugs .motor starts hard smokes badly at low speeds . runs great at 2500rpm and above,better than ever. But hard to restart,smokes bad when restarted or idle. thanx in advance-th
-
06-24-2019, 01:35 PM #2
Make sure you do not have primer solenoid open. It is a black solenoid that opens when you push in key on cold starts. There is a red lever that is used to manually open the valve if your key switch or solenoid fails. You may have left it in open position.
-
06-24-2019, 02:59 PM #3Banned
- Join Date
- Jan 2015
- Location
- Wisconsin
- Posts
- 2,331
- Thanks (Given)
- 458
- Thanks (Received)
- 343
- Likes (Given)
- 6429
- Likes (Received)
- 5147
- Mentioned
- 4 Post(s)
- Tagged
- 0 Thread(s)
Have seen idle and mid air bleeds installed in each others position, and then...................
-
06-25-2019, 09:37 AM #45000 RPM
- Join Date
- Jun 2009
- Location
- central minnesota
- Posts
- 770
- Thanks (Given)
- 6
- Thanks (Received)
- 30
- Likes (Given)
- 5
- Likes (Received)
- 24
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
its not running rich its overoiling,im going to look for leak in fuel sys befor vro all comments are welcome-thanx -th
-
06-25-2019, 11:53 AM #5Banned
- Join Date
- Jan 2015
- Location
- Wisconsin
- Posts
- 2,331
- Thanks (Given)
- 458
- Thanks (Received)
- 343
- Likes (Given)
- 6429
- Likes (Received)
- 5147
- Mentioned
- 4 Post(s)
- Tagged
- 0 Thread(s)
Check fuel line and primer with a vacuum pump with gauge. Have seen primer bulbs that would not hold vacuum but would hold to pressure.
Similar Threads
-
2000 EFI 250 pre mix vs auto oiling?
By Steelborn in forum Four Stroke and Direct Injected Two Stroke EnginesReplies: 1Last Post: 08-09-2015, 03:40 PM -
Optimax oiling????
By xsflight in forum Technical DiscussionReplies: 1Last Post: 01-22-2011, 12:47 PM -
DFI Outboard Oiling
By mdc in forum Four Stroke and Direct Injected Two Stroke EnginesReplies: 1Last Post: 05-06-2010, 06:06 AM -
455 Oiling
By wriedt1 in forum Jet Boats, V-Drives and Stern DrivesReplies: 18Last Post: 07-15-2009, 10:09 PM -
225 Pro Max / Over Oiling?
By RLWYAZ in forum Technical DiscussionReplies: 1Last Post: 03-19-2007, 06:41 PM