User Tag List

Thanks Thanks:  0
Likes Likes:  0
Results 1 to 6 of 6

Thread: 2.4 oiler

  1. #1
    Join Date
    Dec 2002
    Location
    Southside, Al.
    Posts
    1,243
    Thanks (Given)
    54
    Thanks (Received)
    39
    Likes (Given)
    81
    Likes (Received)
    396
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)

    2.4 oiler

    Thinking I might want to put the oiling system back on the two 2.4 Bridgports, so looking for two complete set ups.

  2. #2
    Join Date
    Dec 2001
    Posts
    9,503
    Thanks (Given)
    23
    Thanks (Received)
    270
    Likes (Given)
    191
    Likes (Received)
    1975
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    do not go that way..... if ya want I have all parts short of crank gear..... new only...

  3. #3
    Join Date
    Dec 2001
    Posts
    9,503
    Thanks (Given)
    23
    Thanks (Received)
    270
    Likes (Given)
    191
    Likes (Received)
    1975
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    I was saying use only a new crank gear..... oil injt ..... made a lot of $$$$$ for us fixing motors.....

  4. #4
    Join Date
    Dec 2002
    Location
    Southside, Al.
    Posts
    1,243
    Thanks (Given)
    54
    Thanks (Received)
    39
    Likes (Given)
    81
    Likes (Received)
    396
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)
    Thanks Dave, Was hoping that with all the one's removed I could pick up a couple used set ups reasonably (cheaply). There should be a few out there gathering dust.

  5. #5
    Join Date
    Dec 2001
    Posts
    9,503
    Thanks (Given)
    23
    Thanks (Received)
    270
    Likes (Given)
    191
    Likes (Received)
    1975
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    I am sure I have them.... all parts but I would not do it. At 6000rpm the crank gear at 1 foot in dia is moving at 100 fps. The early ones had a plastic piece that held a magnet to read the speed and check with coil speed so if the gear went bad the alarm would beep. That plastic thing would create drag and wear the crank gear out. Newer motors2.5 have no plastic just a bronze bearing, and a smaller shaft as to give less drag. But NO alarm.

  6. #6
    Join Date
    Dec 2002
    Location
    Southside, Al.
    Posts
    1,243
    Thanks (Given)
    54
    Thanks (Received)
    39
    Likes (Given)
    81
    Likes (Received)
    396
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)
    OK Dave, Thanks. You've convinced me.

Similar Threads

  1. Mercury Tech: Oiler vs Non oiler crankshaft
    By Banana Boat in forum Technical Discussion
    Replies: 5
    Last Post: 10-04-2008, 10:31 AM
  2. DIfference b/w 2.0L non-oiler and 2.4L non-oiler cranks
    By bigshrimpin in forum Technical Discussion
    Replies: 5
    Last Post: 10-21-2007, 10:26 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Aeromarine Research