User Tag List
Thanks: 0
Likes: 0
Results 1 to 6 of 6
Thread: 2.4 oiler
-
03-20-2019, 02:00 PM #16000 RPM
- Join Date
- Dec 2002
- Location
- Southside, Al.
- Posts
- 1,243
- Thanks (Given)
- 54
- Thanks (Received)
- 39
- Likes (Given)
- 81
- Likes (Received)
- 396
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
2.4 oiler
Thinking I might want to put the oiling system back on the two 2.4 Bridgports, so looking for two complete set ups.
-
03-20-2019, 07:44 PM #2Screaming And Flying!
- Join Date
- Dec 2001
- Posts
- 9,503
- Thanks (Given)
- 23
- Thanks (Received)
- 270
- Likes (Given)
- 191
- Likes (Received)
- 1975
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
do not go that way..... if ya want I have all parts short of crank gear..... new only...
-
03-21-2019, 06:39 AM #3Screaming And Flying!
- Join Date
- Dec 2001
- Posts
- 9,503
- Thanks (Given)
- 23
- Thanks (Received)
- 270
- Likes (Given)
- 191
- Likes (Received)
- 1975
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I was saying use only a new crank gear..... oil injt ..... made a lot of $$$$$ for us fixing motors.....
-
03-23-2019, 09:57 AM #46000 RPM
- Join Date
- Dec 2002
- Location
- Southside, Al.
- Posts
- 1,243
- Thanks (Given)
- 54
- Thanks (Received)
- 39
- Likes (Given)
- 81
- Likes (Received)
- 396
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Thanks Dave, Was hoping that with all the one's removed I could pick up a couple used set ups reasonably (cheaply). There should be a few out there gathering dust.
-
03-23-2019, 07:28 PM #5Screaming And Flying!
- Join Date
- Dec 2001
- Posts
- 9,503
- Thanks (Given)
- 23
- Thanks (Received)
- 270
- Likes (Given)
- 191
- Likes (Received)
- 1975
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I am sure I have them.... all parts but I would not do it. At 6000rpm the crank gear at 1 foot in dia is moving at 100 fps. The early ones had a plastic piece that held a magnet to read the speed and check with coil speed so if the gear went bad the alarm would beep. That plastic thing would create drag and wear the crank gear out. Newer motors2.5 have no plastic just a bronze bearing, and a smaller shaft as to give less drag. But NO alarm.
-
03-26-2019, 03:22 PM #66000 RPM
- Join Date
- Dec 2002
- Location
- Southside, Al.
- Posts
- 1,243
- Thanks (Given)
- 54
- Thanks (Received)
- 39
- Likes (Given)
- 81
- Likes (Received)
- 396
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
OK Dave, Thanks. You've convinced me.
Similar Threads
-
Mercury Tech: Oiler vs Non oiler crankshaft
By Banana Boat in forum Technical DiscussionReplies: 5Last Post: 10-04-2008, 10:31 AM -
DIfference b/w 2.0L non-oiler and 2.4L non-oiler cranks
By bigshrimpin in forum Technical DiscussionReplies: 5Last Post: 10-21-2007, 10:26 AM