Mercury Chopper II 14.5 x 28 Steve Smith Offshore Cut

[RoyE]

This prop was sold to me as a Steve Smith Offshore Cut. I'm not sure how to verify it, do the Steve Smith props have any stampings on them? If anyone wants additional pics, I can make them and send them to you.
The prop is in excellent condition. Flo Torq hub system (hub not included).



I'm located in the Netherlands and will accept PayPal.
$525 shipped to the US (This excludes any taxes or import duties that may apply)

[Astromeyer]

What did you run it on? RPM and MPH??

[RoyE]

I ran it on a Piranha Espada 16ft v-hull, not exactly a high performance hull, with a 2.0 135 V6.

It ran 69 mph @ 6300 RPM. It didn't have enough lift for my boat. Didn't seem to really hook up, which may explain the relatively high slip of 17%.

[Astromeyer]

I have a 20’ vas’s boat with a 225 pro max. Just thinking how it would do for me

[Baker343]

This prop was sold to me as a Steve Smith Offshore Cut. I'm not sure how to verify it, do the Steve Smith props have any stampings on them? If anyone wants additional pics, I can make them and send them to you.
The prop is in excellent condition. Flo Torq hub system (hub not included).



I'm located in the Netherlands and will accept PayPal.
$525 shipped to the US (This excludes any taxes or import duties that may apply)

I purchased 3 props from Steve and none of them have any markings identifying his work.
He had 2 cuts that look very similar, Offshore and a Dunamis. Both work very well on lighter set ups.
I believe the Offshore provided a little more lift the Dunamis not so much.
I have both in a 24p and the Dunamis was slightly quicker and faster on my Baker.
I wish he was still cutting props. Great guy to work with

[RoyE]

I have a 20’ vas’s boat with a 225 pro max. Just thinking how it would do for me

I have no experience with such a boat/motor combo so I would't know, maybe someone will chime in that can give you some advice.

I purchased 3 props from Steve and none of them have any markings identifying his work.
He had 2 cuts that look very similar, Offshore and a Dunamis. Both work very well on lighter set ups.
I believe the Offshore provided a little more lift the Dunamis not so much.
I have both in a 24p and the Dunamis was slightly quicker and faster on my Baker.
I wish he was still cutting props. Great guy to work with

Thanks for the info!

[pappa pete]

Talked to Steve Smith yesterday, he's finally getting settled into his new place and is starting to work a little on props again, said he will be getting back to everyone on scream and fly shortly

[Merc 2.5]

I have a 20’ vas’s boat with a 225 pro max. Just thinking how it would do for me

If it dosent have enough lift for a 16ft bote I doubt its gonna lift a 20ft, I wanted the prop to til I read not enough lift , , then again a big jackplate may b what it needed.

On other hand if u have a lighter hull , like a stream it will have plenty lift and turn sum serious rpm , great looking prop , and glws,

[Tranq]

How it will be for phantom 23 with 300 promax 1.62 gear ratio? afraid too much RPM?

[RoyE]

If it dosent have enough lift for a 16ft bote I doubt its gonna lift a 20ft, I wanted the prop to til I read not enough lift , , then again a big jackplate may b what it needed.

On other hand if u have a lighter hull , like a stream it will have plenty lift and turn sum serious rpm , great looking prop , and glws,

I agree, however my 16ft boat has quite a large hook by design. I really need lift to make to boat perform properly. A Hoss Hyperdrive 4 blade performs really well on my setup and so does a TXP OT4. I can imagine it would perform well on a light stream.

How it will be for phantom 23 with 300 promax 1.62 gear ratio? afraid too much RPM?

I think the boat will ride very wet because of the lack of lift. I think this prop is really for light hulls that don't need a lot of lift.

[Varmint]

it looks like it was cut for an allison, with lotsa natural bow lift

I agree, however my 16ft boat has quite a large hook by design. I really need lift to make to boat perform properly. A Hoss Hyperdrive 4 blade performs really well on my setup and so does a TXP OT4. I can imagine it would perform well on a light stream.




I think the boat will ride very wet because of the lack of lift. I think this prop is really for light hulls that don't need a lot of lift.

[RoyE]

ttt

[Sdspropshop]

If you will take $475 for the prop, I will take it.

This prop was sold to me as a Steve Smith Offshore Cut. I'm not sure how to verify it, do the Steve Smith props have any stampings on them? If anyone wants additional pics, I can make them and send them to you.
The prop is in excellent condition. Flo Torq hub system (hub not included).



I'm located in the Netherlands and will accept PayPal.
$525 shipped to the US (This excludes any taxes or import duties that may apply)

[RoyE]

Steve changed plans, it is still for sale

[rgleblanc]

is it still for sale ?