User Tag List
Results 46 to 55 of 55
Thread: Aftermarket Reeds for OMC V6
-
02-05-2019, 07:50 PM #467000 RPM
- Join Date
- Mar 2009
- Location
- Port Saint Lucie
- Posts
- 2,523
- Thanks (Given)
- 3
- Thanks (Received)
- 31
- Likes (Given)
- 6
- Likes (Received)
- 250
- Mentioned
- 0 Post(s)
- Tagged
- 1 Thread(s)
spoke to CCMS and they are good. Ill be sure to check all the cages good for being flat. I only looked at one so far. Reeds are super nice. Im looking forward to seeing how smooth its gonna run. Always had a snotty idle.
-
02-06-2019, 10:58 AM #475000 RPM
- Join Date
- Oct 2017
- Location
- Hugo, MN
- Posts
- 326
- Thanks (Given)
- 36
- Thanks (Received)
- 18
- Likes (Given)
- 62
- Likes (Received)
- 81
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
02-06-2019, 11:13 AM #48Banned
- Join Date
- Jan 2015
- Location
- Wisconsin
- Posts
- 2,331
- Thanks (Given)
- 458
- Thanks (Received)
- 343
- Likes (Given)
- 6429
- Likes (Received)
- 5147
- Mentioned
- 4 Post(s)
- Tagged
- 0 Thread(s)
Not my words, something I copied off of this site after using the search feature. I forget who this was, sorry.
Lapping reed cages-Rub in a Figure 8 motion on a 12”x12”x1/4”
sheet of glass , first clean cage and spray surface to be lapped with machinist lay out dye let it dry then rub on 220 wet and dry sandpaper till all dye is removed then go over it with 400 to give it a smoother texture ..
-
02-06-2019, 11:48 AM #495000 RPM
- Join Date
- Oct 2017
- Location
- Hugo, MN
- Posts
- 326
- Thanks (Given)
- 36
- Thanks (Received)
- 18
- Likes (Given)
- 62
- Likes (Received)
- 81
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Thank you!
-
02-06-2019, 12:58 PM #50Supporting Vendor
- Join Date
- Apr 2001
- Location
- Brookeland , Texas 75931 North of Jasper
- Posts
- 11,838
- Thanks (Given)
- 4
- Thanks (Received)
- 163
- Likes (Given)
- 11
- Likes (Received)
- 795
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Hum your quoting my post , I’ll flattered))
JayJay @ JSRE
-
02-06-2019, 03:05 PM #51Banned
- Join Date
- Jan 2015
- Location
- Wisconsin
- Posts
- 2,331
- Thanks (Given)
- 458
- Thanks (Received)
- 343
- Likes (Given)
- 6429
- Likes (Received)
- 5147
- Mentioned
- 4 Post(s)
- Tagged
- 0 Thread(s)
-
02-06-2019, 07:14 PM #52
We have some really great vendors and builders here , I take everything they say to heart and run with it 99% of the time !! This kinda stuff is priceless to me or youd spend tons of $$ figuring lots of this stuff out
-
02-09-2019, 01:17 AM #53
On Stokers dyno my 4.4 V8 rude using a set of reeds from TDR lost 22 hp to a set of Boysen reeds. 428hp TDR vs 450hp Boysen. I ran the TDR reeds anyway to see how long they would last. I ran the engine for 4 seasons and 160 hours when I had a problem with one of the exhaust ports leaking water into the cylinder that caused me to remove the engine. The reeds looked like new when I tore it down.
-
02-09-2019, 10:41 AM #54Supporting Vendor
- Join Date
- Apr 2001
- Location
- Brookeland , Texas 75931 North of Jasper
- Posts
- 11,838
- Thanks (Given)
- 4
- Thanks (Received)
- 163
- Likes (Given)
- 11
- Likes (Received)
- 795
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
I freshen up motors with the TDR reeds installed all the time from all out race to recreational inspect and put the same reeds back in , my ME high points champion Gary Henning sent me Drag with 360 10,500 rpm passes to refresh , the motors was just about to self destruct caught it in time , I refreshed motor put same reeds back in next week end he won high points championship at Firebird world finals ...
I’d like to say , in a open forum Im not going to knock anyone’s products lots of great products on the market, I’m reporting what performance and longevity I see using the TDR reeds and other products that’s hit
1000 out of the box , choose what reed and or any product you choose still a free country till the socialist gain power ... )))
JayLast edited by Jay Smith; 02-09-2019 at 11:38 AM.
Jay @ JSRE
-
02-11-2019, 12:56 AM #55
Similar Threads
-
Mercury Tech: fiber reeds and steel reeds in same motor
By buzmacdowell in forum Technical DiscussionReplies: 4Last Post: 07-09-2011, 10:06 PM -
oem vs aftermarket
By k-man in forum Technical DiscussionReplies: 9Last Post: 03-21-2009, 02:00 PM