User Tag List

Thanks Thanks:  0
Likes Likes:  0
Results 1 to 8 of 8
  1. #1
    Join Date
    Nov 2006
    Location
    Tampa, Fl
    Posts
    160
    Thanks (Given)
    0
    Thanks (Received)
    6
    Likes (Given)
    0
    Likes (Received)
    19
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    3.0L sportmaster prop shaft seal replacement

    I need to replace the prop shaft seals. Is pulling the carrier out required or can it be done from the outside?

  2. #2
    Join Date
    Aug 2012
    Location
    Tenkiller Lake, OK
    Posts
    520
    Thanks (Given)
    3
    Thanks (Received)
    34
    Likes (Given)
    137
    Likes (Received)
    209
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Best to pull the carrier to do it. I have seen hacks that drill small hole in the seals, screw a screw into them and use a slide hammer to pull it out from the outside. Remember there are at least two seals to remove.

  3. #3
    Join Date
    Jan 2002
    Location
    JAX. FLORIDA
    Posts
    4,277
    Thanks (Given)
    28
    Thanks (Received)
    30
    Likes (Given)
    386
    Likes (Received)
    154
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    I have Charlie and Ed pull my carrier each year to inspect my gears and replace my seals and water pump, just as insurance.

    "Confidence" is that wonderful feeling you had right before you fully understood your true situation.- Unknown
    I don’t know what effect these men will have upon the enemy, but, by God, they terrify me.- Duke of Wellington
    “I am not afraid of an Army of lions lead by a sheep; I am afraid of sheep lead by a lion.” – Alexander the Great
    Whoever said the pen is mightier than the sword obviously never encountered automatic weapons.-Douglas MacArthur

    Allison GSE 300XS

  4. #4
    Join Date
    Feb 2009
    Location
    Edgewater,B.C. CANADA
    Posts
    8,260
    Thanks (Given)
    179
    Thanks (Received)
    321
    Likes (Given)
    3578
    Likes (Received)
    1236
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Pull the carrier there is a seal installer that positions the seals at the correct depth and ensures they are installed square in the carrier.

    Dave
    1980 Cougar 19 tunnel,90 2.4L Bridgeport EFI in middle of restoration.
    1988 BAJA Sunsport 186, 96 225 Pro Max
    79 12' Auminum, 95 Merc 9.9
    RIP Stu
    "So many idiots, so few bullets"

  5. #5
    Join Date
    Jul 2016
    Location
    columbia sc
    Posts
    190
    Thanks (Given)
    2
    Thanks (Received)
    1
    Likes (Given)
    2
    Likes (Received)
    4
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Do you know where we can pick up that seal install tool

  6. #6
    Join Date
    Nov 2006
    Location
    Tampa, Fl
    Posts
    160
    Thanks (Given)
    0
    Thanks (Received)
    6
    Likes (Given)
    0
    Likes (Received)
    19
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    I guess I will run it over to Colabella and have him reseal it. I was just hoping to avoid the 4 hour round trip in the car over just a couple of seals.

  7. #7
    Join Date
    Feb 2009
    Location
    Edgewater,B.C. CANADA
    Posts
    8,260
    Thanks (Given)
    179
    Thanks (Received)
    321
    Likes (Given)
    3578
    Likes (Received)
    1236
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    I have the Merc part number but dealer probably would have to order it.

    Dave
    1980 Cougar 19 tunnel,90 2.4L Bridgeport EFI in middle of restoration.
    1988 BAJA Sunsport 186, 96 225 Pro Max
    79 12' Auminum, 95 Merc 9.9
    RIP Stu
    "So many idiots, so few bullets"

  8. #8
    Join Date
    Feb 2009
    Location
    Edgewater,B.C. CANADA
    Posts
    8,260
    Thanks (Given)
    179
    Thanks (Received)
    321
    Likes (Given)
    3578
    Likes (Received)
    1236
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Part number 91816294.

    Dave
    1980 Cougar 19 tunnel,90 2.4L Bridgeport EFI in middle of restoration.
    1988 BAJA Sunsport 186, 96 225 Pro Max
    79 12' Auminum, 95 Merc 9.9
    RIP Stu
    "So many idiots, so few bullets"

Similar Threads

  1. Mercury Tech: Shift shaft seal replacement: Any tips?
    By mxz in forum Technical Discussion
    Replies: 11
    Last Post: 05-27-2014, 08:06 AM
  2. 3.0 225 lower unit prop seal replacement?
    By BUD in forum Technical Discussion
    Replies: 0
    Last Post: 12-29-2011, 06:37 PM
  3. sportmaster prop shaft seal
    By boise137 in forum Technical Discussion
    Replies: 5
    Last Post: 05-29-2006, 08:43 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Aeromarine Research