User Tag List
Results 91 to 105 of 146
Thread: Well,I concede.Almost!!
-
01-23-2019, 04:27 PM #91
-
02-05-2019, 04:27 PM #92
Well,contrary to popular belief I haven't been on a seven day drunk! It's just been COLD, and what little ambition I have, Ive used to keep warm and plow snow. Anyway,some work has progressed on the boat.Two more stringers are in, and a throttle pad is set. Stringers were set in an epoxy paste then covered with eight and a half oz fabric,another ten oz four inch tape will be set at the floor seam.The throttle pad was fabbed from a piece of Hydrotec,with a top and bottom cover of 1700. T nuts were pre installed for the Hot Foot.Next will be the rear seat bulkhead.
-
-
02-11-2019, 03:12 PM #93
-
02-11-2019, 05:05 PM #94
-
NICE PAIR liked this post
-
02-11-2019, 05:51 PM #95
-
NICE PAIR liked this post
-
02-12-2019, 03:57 PM #96
-
NICE PAIR liked this post
-
02-12-2019, 04:09 PM #97Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,753
- Thanks (Given)
- 381
- Thanks (Received)
- 1305
- Likes (Given)
- 5602
- Likes (Received)
- 11033
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
If you store the boat on a roller trailer, you might benefit from a short keel stringer to keep the bottom from deflecting. Outstanding work on the old girl....
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
-
NICE PAIR liked this post
-
02-12-2019, 05:16 PM #98
Thanks,but the only way I would even take a free roller trailer,is if it could easily be converted to bunks
-
NICE PAIR liked this post
-
02-12-2019, 05:35 PM #99
Well if that fuel tank doesn't fit when your done......I know somebody who would like it.......
Your going to be ready for Pete's RompJames H. W2F a V-King... Want 2 Fly a V-King
Dedicated Site for Hydrostreams >> http://hydrostreamforums.com/
My Project 1979 V-King restore >> http://hydrostreamforums.com/viewtopic.php?f=9&t=2761
-
NICE PAIR liked this post
-
02-12-2019, 05:38 PM #100Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,753
- Thanks (Given)
- 381
- Thanks (Received)
- 1305
- Likes (Given)
- 5602
- Likes (Received)
- 11033
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
A standard trailer with rollers on the keel and bunks at the sides was what I meant. When the keel sits on the rollers it can deform the bottom over time.
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
-
NICE PAIR liked this post
-
02-12-2019, 06:26 PM #101
Good advice,I dimpled the bottom of a vector that way.My trailer now has the bunks adjusted so when loaded the rollers are 1/4" from touching the pad,but still roll on the bow when loading.
James,That tank is a little small (12 gal) but just can't bring myself to give it up.Want to build a new oval one 18 gal.
-
W2F a V-King liked this post
-
02-13-2019, 03:46 PM #102
-
02-13-2019, 04:36 PM #103
-
NICE PAIR liked this post
-
02-13-2019, 04:39 PM #104
-
NICE PAIR liked this post
-
02-13-2019, 07:11 PM #105James H. W2F a V-King... Want 2 Fly a V-King
Dedicated Site for Hydrostreams >> http://hydrostreamforums.com/
My Project 1979 V-King restore >> http://hydrostreamforums.com/viewtopic.php?f=9&t=2761