User Tag List
Thanks: 0
Results 1 to 15 of 17
Thread: Cutting and welding driveshafts
-
11-26-2018, 12:32 PM #1Member
- Join Date
- Oct 2009
- Location
- Lake Conroe, Tx
- Posts
- 63
- Thanks (Given)
- 4
- Thanks (Received)
- 2
- Likes (Given)
- 6
- Likes (Received)
- 30
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Cutting and welding driveshafts
Got a 25 in lower and need a 20 in. Anybody had success cutting and welding shafts? I think i could make a jig to keep it inline while it was being welded. Any tips?
-
11-26-2018, 01:14 PM #2Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,753
- Thanks (Given)
- 381
- Thanks (Received)
- 1305
- Likes (Given)
- 5602
- Likes (Received)
- 11033
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
Most just cut and re-spline
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
-
11-26-2018, 01:21 PM #3
-
-
11-27-2018, 08:19 AM #4Supporting Vendor
- Join Date
- Sep 2006
- Location
- Key Largo, Fl
- Posts
- 3,272
- Thanks (Given)
- 8
- Thanks (Received)
- 215
- Likes (Given)
- 30
- Likes (Received)
- 585
- Mentioned
- 1 Post(s)
- Tagged
- 1 Thread(s)
we can cut and respline shaft still in the case.
-
11-27-2018, 08:19 AM #5
Chris Carson can hook you up, sure a few others to but u can call or PM chris
-
11-27-2018, 10:07 AM #6
Is a heat treat needed after respline?
Azure AZ259, 8.1
-
11-27-2018, 02:57 PM #7Supporting Vendor
- Join Date
- Sep 2006
- Location
- Key Largo, Fl
- Posts
- 3,272
- Thanks (Given)
- 8
- Thanks (Received)
- 215
- Likes (Given)
- 30
- Likes (Received)
- 585
- Mentioned
- 1 Post(s)
- Tagged
- 1 Thread(s)
Yes
-
tux974 liked this post
-
11-29-2018, 10:40 AM #8
How about adding to one ? I need 2 fat shaft sport masters 15 inch made to 20" ?
Variety of stuff
-
11-30-2018, 07:56 AM #9Supporting Vendor
- Join Date
- Sep 2006
- Location
- Key Largo, Fl
- Posts
- 3,272
- Thanks (Given)
- 8
- Thanks (Received)
- 215
- Likes (Given)
- 30
- Likes (Received)
- 585
- Mentioned
- 1 Post(s)
- Tagged
- 1 Thread(s)
yes we can can make them longer by using coupler and longer top shaft
-
12-02-2018, 09:27 PM #10
Chris Carson - Are yall capable of heat treating?
Are the driveshafts on 59" merc 3 cylinders heat treatable? I know they have the spin welds from the factory, wasn't sure if the lower part of the shaft was a different alloy or not.
Thanks,
Jim
Cracker Bay Thundercats
-
12-03-2018, 10:33 AM #11
Get it HOT with a torch , dip in water Voila
We have invented the world; WE see
-
12-03-2018, 01:36 PM #12Supporting Vendor
- Join Date
- Sep 2006
- Location
- Key Largo, Fl
- Posts
- 3,272
- Thanks (Given)
- 8
- Thanks (Received)
- 215
- Likes (Given)
- 30
- Likes (Received)
- 585
- Mentioned
- 1 Post(s)
- Tagged
- 1 Thread(s)
yes all shafts need heat treating when cut and machined. we do it all.
-
12-03-2018, 01:53 PM #13Member
- Join Date
- Oct 2009
- Location
- Lake Conroe, Tx
- Posts
- 63
- Thanks (Given)
- 4
- Thanks (Received)
- 2
- Likes (Given)
- 6
- Likes (Received)
- 30
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Chris, what would it cost to go from a 15in cle to coupled 20in. I have a cle that i would like to be able to use as a backup 20in. Thanks
-
12-03-2018, 04:17 PM #14Supporting Vendor
- Join Date
- Sep 2006
- Location
- Key Largo, Fl
- Posts
- 3,272
- Thanks (Given)
- 8
- Thanks (Received)
- 215
- Likes (Given)
- 30
- Likes (Received)
- 585
- Mentioned
- 1 Post(s)
- Tagged
- 1 Thread(s)
200.00
-
euro scott liked this post
-
12-05-2018, 12:46 PM #15Member
- Join Date
- Oct 2009
- Location
- Lake Conroe, Tx
- Posts
- 63
- Thanks (Given)
- 4
- Thanks (Received)
- 2
- Likes (Given)
- 6
- Likes (Received)
- 30
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Chris, i would like to get one of the 15 to 20 in coupler/shafts. I will be putting it in a merc fishing motor mid with the bucket pulled. Please let me know how to pay, pay pal or? Thanks
Similar Threads
-
I need driveshafts
By Bruster in forum Parts WantedReplies: 2Last Post: 07-06-2015, 12:15 PM -
What type of stainless did omc use in their driveshafts? For welding purposes.
By ernstudet22 in forum Technical DiscussionReplies: 1Last Post: 02-04-2008, 10:29 AM -
cutting driveshafts
By Action Frank in forum Technical DiscussionReplies: 4Last Post: 01-10-2007, 07:55 PM -
who's cutting driveshafts???
By Jerry Ridenour in forum Technical DiscussionReplies: 11Last Post: 06-14-2004, 05:19 AM -
cutting and welding Drive shaft?
By CNT in forum Technical DiscussionReplies: 9Last Post: 06-05-2004, 10:21 AM