User Tag List
Thanks: 0
Likes:
Results 1 to 7 of 7
Thread: Mercury 1.25" solid hub inserts
-
10-12-2018, 08:13 PM #1
5000 RPM
- Join Date
- May 2001
- Location
- Maine
- Posts
- 982
- Thanks (Given)
- 5
- Thanks (Received)
- 35
- Likes (Given)
- 42
- Likes (Received)
- 170
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Mercury 1.25" solid hub inserts
Does anyone know if its possible to purchase the 4 plastic/ teflon inserts that attach to the Mercury solid hub - #840389 K06? Is there a part number?
Thanks...Last edited by 4Speed; 10-12-2018 at 08:17 PM.
-
lance liked this post
-
10-13-2018, 11:36 AM #2
5000 RPM
- Join Date
- Jun 2002
- Location
- Northern Utah
- Posts
- 454
- Thanks (Given)
- 3
- Thanks (Received)
- 8
- Likes (Given)
- 7
- Likes (Received)
- 24
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Yes,
840382A02 black snubber strip replacement kit
-
10-13-2018, 12:36 PM #3
5000 RPM
- Join Date
- May 2001
- Location
- Maine
- Posts
- 982
- Thanks (Given)
- 5
- Thanks (Received)
- 35
- Likes (Given)
- 42
- Likes (Received)
- 170
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I expect the way to determine if they need replacement is to slide the hub into the prop and ensure its "snug" fit with no metal to metal contact(?)
-
10-13-2018, 05:57 PM #4
5000 RPM
- Join Date
- Jun 2002
- Location
- Northern Utah
- Posts
- 454
- Thanks (Given)
- 3
- Thanks (Received)
- 8
- Likes (Given)
- 7
- Likes (Received)
- 24
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I guess they could wear out but I've had more of a problem just keeping them glued on. I've even seen new hubs with the strips loose in the box.
I have experienced the same hub fitting tight in one prop but loose in another.
I think if all 4 of the snubber strips are attached to the hub and you torque the nut down properly, you will be fine.
-
10-13-2018, 08:21 PM #5
5000 RPM
- Join Date
- May 2001
- Location
- Maine
- Posts
- 982
- Thanks (Given)
- 5
- Thanks (Received)
- 35
- Likes (Given)
- 42
- Likes (Received)
- 170
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I was thinking of trying some 5200 adhesive silicone to re glue my loose strips.
-
10-13-2018, 09:03 PM #6
Supporting Vendor
- Join Date
- Jun 2006
- Location
- Silverton section of Toms River, NJ/Stuart, Florida
- Posts
- 10,205
- Thanks (Given)
- 374
- Thanks (Received)
- 314
- Likes (Given)
- 821
- Likes (Received)
- 1999
- Mentioned
- 1 Post(s)
- Tagged
- 1 Thread(s)
Use bellows ashesive
-
Dave Strong liked this post
-
10-19-2018, 11:04 AM #7
5000 RPM
- Join Date
- Aug 2010
- Location
- Barrie, Ontario, Canada
- Posts
- 342
- Thanks (Given)
- 30
- Thanks (Received)
- 23
- Likes (Given)
- 148
- Likes (Received)
- 107
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Is there a part number for the round plastic inner insert in the hub? Not sure if it wears down over time causing a little bit of play on the propshaft?
Last edited by V-bottom; 10-19-2018 at 11:06 AM.
Triad V21 #002 - 15in DBR 300 xs
19' J-Craft - 175 Opti
18' Pontoon - 115 CT 4S
Reply With Quote
Similar Threads
-
Mercury Outboard Cowl hose inserts??!?!?
By Superboat Rob in forum Props, Setup, and RiggingReplies: 12Last Post: 03-13-2007, 08:10 PM -
EGT extension wire type K "solid?"
By B.Mac in forum Technical DiscussionReplies: 9Last Post: 03-16-2004, 10:35 PM -
x-flow v-4 solid mounts? "pinning"?
By sixabove in forum Technical DiscussionReplies: 0Last Post: 05-28-2002, 10:51 AM
