User Tag List
Results 16 to 21 of 21
-
09-30-2018, 03:09 PM #16
It is a 13 or a 15? Cool boat! I love that you and your dad made it a two seater!!!
https://www.glen-l.com/designs/outboard/tuffy.html
One thing I would do, is look at a jackplate that would better suit your needs. The only plates I see that Bob's has are way over kill (for 300hp heavy motors), less the 40hp jackplate which isn't enough.... ?
You can move weight around in the boat that may help. Where are the fuel tank and battery?
How about some pictures of the bilge when finished? Any running pics?
-
Callum5009 thanked for this post
-
09-30-2018, 05:11 PM #17Junior Member
- Join Date
- Jul 2018
- Location
- Toronto, Ontario
- Posts
- 18
- Thanks (Given)
- 2
- Thanks (Received)
- 1
- Likes (Given)
- 1
- Likes (Received)
- 2
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I would get power trim but it's a short shaft and they're really hard to find. The best thing I've found is CMC and it's around $600
-
09-30-2018, 06:53 PM #18Screaming And Flying!
- Join Date
- Dec 2001
- Posts
- 9,502
- Thanks (Given)
- 23
- Thanks (Received)
- 271
- Likes (Given)
- 191
- Likes (Received)
- 1976
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Put a L brace on the green board. Flatys don't really need setback. Just a good surfacing prop.
-
10-05-2018, 10:42 AM #19Junior Member
- Join Date
- Jul 2018
- Location
- Toronto, Ontario
- Posts
- 18
- Thanks (Given)
- 2
- Thanks (Received)
- 1
- Likes (Given)
- 1
- Likes (Received)
- 2
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
thanks for all your help guys, I really appreciate it.
-
10-06-2018, 12:25 PM #20
6 inch jack plate with a 60hp twin and you'll be fine, but if your not sure then just add 2 extra knee's and put them up as high as you can and long as you can within reason. you want these about 4 inches outside what will be the bolt holes for the jack plate at the top.. if you dont want to add too much extra weight then cut some large circles out the wood and just seal everything with resin of your choice.. you will have a much stiffer boat with 2 knee's rather than just that small short one on their now. and it will be a stronger transom that could hold a 125hp easy.
-
10-21-2018, 02:06 PM #21Junior Member
- Join Date
- Jul 2018
- Location
- Toronto, Ontario
- Posts
- 18
- Thanks (Given)
- 2
- Thanks (Received)
- 1
- Likes (Given)
- 1
- Likes (Received)
- 2
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
How bout u tell my dad that. I wanted to buy a 3 cyl but he was worried about it.
Similar Threads
-
Setback bracket
By Tripps in forum Misc. Parts and AccessoriesReplies: 0Last Post: 07-24-2016, 04:54 AM -
transom bracket setback and 2 jackplates
By Cary 29 in forum Props, Setup, and RiggingReplies: 12Last Post: 05-10-2012, 06:59 PM -
setback bracket to transom
By ck1flyer in forum Props, Setup, and RiggingReplies: 2Last Post: 06-27-2007, 07:57 AM -
setback bracket
By fyremanbil in forum Technical DiscussionReplies: 2Last Post: 08-23-2001, 07:45 AM