Johnson/Evinrude parts for sale.

[Tinbanger1979]

I have alot of Johnson & Evinrude parts for sale since I switched to Mercury. I have listed some parts and prices below. Make offers on anything your interested in and I have no problem with shipping/PayPal for payment. Pictures to come later today of most of it.

2000 Johnson Ocean Pro 250 with 25" shaft and 200 hours on a total rebuild. Wiseco top pinned pistons with big rods balanced and lightened by John Marles, all new OEM bearings and seals. Block work and porting done by Mike Barajas at MJ performance. One hole had the main jet plug with dirt and burned a hole in that piston. That hole will need bored most likely, don't think honing will clean up enough. Magnum 2 lower unit off 2004 Ficht 250. All new electronics when I rebuilt the motor. No heads, but 2 sets of heads listed below. If someone wants the motor I'll make a package deal with the motor, cowls and a set of heads.
Asking $1500.00 or best offer

Evinrude top mount binnacle, teleflex extreme cables and complete wiring harness and 2 gauges, all removed from my Mako 21 center console boat. This was all purchased new when I rebuilt the motor over the winter. Asking $500.00 or best offer.

2004 Evinrude Ficht 250 3.3 liter block, heads, crank, pistons and rods. One hole lost a ring locator pin so needs bored or sleeved. 125 hours on whole motor. Computer and injectors have already sold.
Asking $500.00 or best offer

Al Stoker 3 liter V6 offset chamber closed deck looper heads, excellent condition.
Asking $500.00 or best offer

Stock 3 liter V6 looper heads cut to 50CC by Monty
Asking $250.00 or best offer

2004 Ficht 250 top cowl and lower cowls, excellent condition. They were just painted Johnson Ocean Pro grey with basecoat/clearcoat paint, no decals.
250.00 or best offer

[Tinbanger1979]

Pictures of some stuff.

[Tinbanger1979]

Bump make offers. I would make a screaming package deal if somone would be interested in the whole list of stuff for sale.

[Tinbanger1979]

Bump, lots of parts still available.

[Instigator]

Might be interested in the 250.

Ill pm you.

[Tinbanger1979]

Here's some pictures of the cowls and lower pans I have for sale. 1 set is from a 2004 Ficht 250 V6 and the other set is from a 2000 Ocean Pro 250 V6. Make an offer if interested. There dusty and have a few small scratches, but they have 2 coats of basecoat and 3 coats of clear coat. So any small imperfections will buff right out. I get a pretty good price on shipping through Fastenal.

[Instigator]

Just realized I never pm'd u about this ad.
Sorry bought that.

PM on its way.

Here's some pictures of the cowls and lower pans I have for sale. 1 set is from a 2004 Ficht 250 V6 and the other set is from a 2000 Ocean Pro 250 V6. Make an offer if interested. There dusty and have a few small scratches, but they have 2 coats of basecoat and 3 coats of clear coat. So any small imperfections will buff right out. I get a pretty good price on shipping through Fastenal.

[laserguy]

I sent you a pm

[Tinbanger1979]

I sent you a pm

I didn't get your PM.

[laserguy]

My number is 757 692 4828

Richard

[Tinbanger1979]

Lower unit, driveshaft have been sold.

Binnacle control, gauges, cables have been sold.

Thanks, S & F members

[ou812]

I have a 1990 225 with a set of your heads work

[Tinbanger1979]

I have a 1990 225 with a set of your heads work

Is your motor an open deck or closed deck? These were all from a closed deck motor. But I think you can use them on a open deck with some slight mods.

[Instigator]

A ‘90 would be open deck but heads will work on it.

Is your motor an open deck or closed deck? These were all from a closed deck motor. But I think you can use them on a open deck with some slight mods.

[Tinbanger1979]

Thanks Instigator.