User Tag List
Thanks: 0
Likes: 0
Results 1 to 9 of 9
-
08-11-2018, 03:43 PM #15000 RPM
- Join Date
- Apr 2016
- Location
- Port perry
- Posts
- 201
- Thanks (Given)
- 2
- Thanks (Received)
- 1
- Likes (Given)
- 0
- Likes (Received)
- 36
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
No spark in one cylinder 89 evinrude 225
Hey guys got my 89 evinrude 225 out today ran fine then on the way to the dock it sounded like it dropped a cylinder and the top starboard cylinder has no spark I swapped coils and still had no spark in the same cylinder with a different coil so does that mean it's my cdi
-
08-14-2018, 05:24 AM #25000 RPM
- Join Date
- Apr 2016
- Location
- Port perry
- Posts
- 201
- Thanks (Given)
- 2
- Thanks (Received)
- 1
- Likes (Given)
- 0
- Likes (Received)
- 36
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Really nothing I guess I'm going to just get a cdi (powerpack) and see if that fixes it
-
08-14-2018, 06:35 PM #3
Could also be the timer base. you'll need to do an ohm reading on it. Look up the CDI trouble shooting book on their site, it gives you all the specs and how to check the components.
"One of the penalties for refusing to participate in politics is that you end up being governed by your inferiors". Plato .
-
08-14-2018, 08:48 PM #45000 RPM
- Join Date
- Apr 2016
- Location
- Port perry
- Posts
- 201
- Thanks (Given)
- 2
- Thanks (Received)
- 1
- Likes (Given)
- 0
- Likes (Received)
- 36
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Really I didn't think that the timer base would cause one cylinder not to spark but u might be on to something cause when I put it in gear and give it gas it just dies u would think it would still run if it was just one cylinder not running
-
08-14-2018, 09:16 PM #5
Now you are describing different symptoms..... How did you check for spark? did you use a spark checker or just pull the wire off while it was running? Did you swap plug wires? Are you sure you are losing only one cylinder? One cylinder not firing won't make it die, but if the whole bank were to drop, then maybe. If your'e dropping the entire stbd bank, it could be the shift interrupter switch engaging due to a stiff shift shaft or it could be a bad stator. Did you check the compression?
"One of the penalties for refusing to participate in politics is that you end up being governed by your inferiors". Plato .
-
08-14-2018, 09:35 PM #65000 RPM
- Join Date
- Apr 2016
- Location
- Port perry
- Posts
- 201
- Thanks (Given)
- 2
- Thanks (Received)
- 1
- Likes (Given)
- 0
- Likes (Received)
- 36
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I pulled all the plugs plugs out and held each one on the block while turning it over only one had no spark I swapped the coil/wire and spark plug with one that was working and the same cylinder had no spark with a different coil
-
08-15-2018, 11:38 AM #75000 RPM
- Join Date
- Apr 2016
- Location
- Port perry
- Posts
- 201
- Thanks (Given)
- 2
- Thanks (Received)
- 1
- Likes (Given)
- 0
- Likes (Received)
- 36
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
How would I go about testing the timer base
-
08-15-2018, 03:53 PM #8
Ohm test it, CDI has a truobleshooting book on their website.
"One of the penalties for refusing to participate in politics is that you end up being governed by your inferiors". Plato .
-
08-28-2018, 08:15 PM #95000 RPM
- Join Date
- Apr 2016
- Location
- Port perry
- Posts
- 201
- Thanks (Given)
- 2
- Thanks (Received)
- 1
- Likes (Given)
- 0
- Likes (Received)
- 36
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Well installed a new power pack from cdi electronics and it seemed to fix it wasn't able to take it off the boat lift yet cause the day I installed it we had tornado warning and one actually touched done didn't stop me from fishing tho lol
Similar Threads
-
Mercury Tech: spark on #3 cylinder only??
By david martin in forum Technical DiscussionReplies: 4Last Post: 07-18-2009, 10:38 AM -
OMC Tech: no spark 1 cylinder
By jay1 in forum Technical DiscussionReplies: 3Last Post: 06-26-2009, 09:38 PM -
spark on only one cylinder
By No Cheap Thrills in forum Technical DiscussionReplies: 9Last Post: 06-13-2008, 06:56 PM -
No spark to #2 cylinder...
By 201pro in forum Technical DiscussionReplies: 5Last Post: 08-29-2005, 06:37 PM -
no spark just one cylinder ??
By djtalon in forum Technical DiscussionReplies: 5Last Post: 07-04-2003, 10:21 PM