User Tag List
Results 391 to 405 of 496
Thread: 13' Bullet 130 Rebuild & Repower
-
06-02-2019, 12:35 PM #391
-
tnelsmn liked this post
-
06-15-2019, 08:09 PM #392
-
06-16-2019, 07:49 AM #3935000 RPM
- Join Date
- Mar 2016
- Location
- cincinnati, ohio
- Posts
- 662
- Thanks (Given)
- 142
- Thanks (Received)
- 32
- Likes (Given)
- 278
- Likes (Received)
- 191
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Dat's some slick cable routing, are you going to leave it like that when you flip the cap and reassemble the top to bottom??? Will you be able to work on it if there is a problem, can you remove a bad wire???
-
06-17-2019, 05:18 AM #3947000 RPM
- Join Date
- Mar 2009
- Location
- Port Saint Lucie
- Posts
- 2,523
- Thanks (Given)
- 3
- Thanks (Received)
- 31
- Likes (Given)
- 6
- Likes (Received)
- 250
- Mentioned
- 0 Post(s)
- Tagged
- 1 Thread(s)
His rigging is very minimal. I believe there is room to pull any wire out if needed. He only has batt cables, harness, shift/throttle and steering hoses. He can leave them in if he wants, they won't be in the way. They do need to be pulled inside to do some glass work on the cap still. Hoping to get the last bit of glassing done here soon so it can have the last body work done before paint.
-
06-17-2019, 05:26 AM #395
I pulled all the cables out and flipped the cap back over. That was just to mock it up. all cables will be reinstalled after the boat is done and cap glassed to the hull itself. I like to mock things up to make sure they fit as intended in case changes are needed, easier to do it now than after its glassed and painted. All my "gauges" will be Bluetooth from my phone so yea my rigging is pretty basic. Only mechanical gauge is the water pressure which is the only hose I did not run but there is plenty of room.. There is plenty of extra space, I can easily pull wires through is needed when installed, the only thing is the plug for the harness has to go through the rear hole first with no cables otherwise it wont fit. Should be clean simple looking boat in the end.
Last edited by TwzteD; 06-17-2019 at 05:31 AM.
-
JPEROG liked this post
-
06-19-2019, 06:34 PM #396
It's wet, so you can't see the glass... but this was my under-deck solution for cable management haha. 2" I.d. PVC pipe, cut in 1" lengths. Some wood sawdust mixed in with epoxy, and a strip of glass through it. I whacked them with a hammer afterwards and they didn't pop.
Yours look better though haha.
1) 1995 14' Bayliner Restoration <--Click
2) Home-Made Tunnel-Boat Project <--Click
-
TwzteD liked this post
-
06-19-2019, 09:19 PM #397
-
06-20-2019, 03:22 PM #3981) 1995 14' Bayliner Restoration <--Click
2) Home-Made Tunnel-Boat Project <--Click
-
TwzteD liked this post
-
06-20-2019, 08:59 PM #399
-
06-20-2019, 09:17 PM #4007000 RPM
- Join Date
- Mar 2009
- Location
- Port Saint Lucie
- Posts
- 2,523
- Thanks (Given)
- 3
- Thanks (Received)
- 31
- Likes (Given)
- 6
- Likes (Received)
- 250
- Mentioned
- 0 Post(s)
- Tagged
- 1 Thread(s)
Perfect!
-
06-21-2019, 07:09 AM #401
I think so too, should be perfect.
-
06-21-2019, 07:14 AM #402Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,701
- Thanks (Given)
- 380
- Thanks (Received)
- 1280
- Likes (Given)
- 5599
- Likes (Received)
- 10934
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
Might cover some of the upper intake holes. It may suck air and kill your impeller. Or just go to a hull mounted intake. Orrrr, a lwp lower.
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
-
06-21-2019, 08:54 AM #403
-
06-21-2019, 02:09 PM #404
Well.. looks like photbucket watermarked all of my pictures...
-
06-21-2019, 02:24 PM #405
Ready to see how it floats, Guess ill stop using photbucket, it was alot easier as i could do everything easy from my phone.
-
JPEROG liked this post
Similar Threads
-
Evinrude XP200 Rebuild or Repower
By Stoker88 in forum Props, Setup, and RiggingReplies: 6Last Post: 09-09-2020, 11:06 PM -
83 Bullet Rebuild Update
By One Oldman in forum Fiberglass and Composites DiscussionReplies: 2Last Post: 06-02-2013, 10:10 PM -
30' velocity rebuild/repower/reeverything
By biohzrd in forum General Boating DiscussionReplies: 66Last Post: 08-03-2010, 10:39 AM -
Repower advice: OptiMax or rebuild 2.5EFI
By mercfan1 in forum General Boating DiscussionReplies: 8Last Post: 11-11-2008, 09:02 PM