User Tag List
Thanks: 0
Likes: 0
Results 1 to 8 of 8
-
03-05-2018, 01:54 AM #1Junior Member
- Join Date
- Mar 2018
- Location
- Kaiapoi, New Zealand
- Posts
- 8
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
How to change gear oil on evinrude super strangler
I have an evinrude super stranger and there doesn't seem to have a bottom bung to drain gear oil only two bungs above the cav. Plate
-
03-06-2018, 04:17 PM #2Screaming And Flying!
- Join Date
- Dec 2001
- Posts
- 9,502
- Thanks (Given)
- 23
- Thanks (Received)
- 271
- Likes (Given)
- 191
- Likes (Received)
- 1976
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I would think if you trimed it up most oil would come out the front screw. Then use Low pressure air to blow out some more. Low so ya don't blow the seals. Or get a oil pump for lower grease and pump till clean oil comes out. Is it a 1/1 lower or the big case?
-
03-06-2018, 04:32 PM #3Junior Member
- Join Date
- Mar 2018
- Location
- Kaiapoi, New Zealand
- Posts
- 8
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
03-06-2018, 06:23 PM #4Screaming And Flying!
- Join Date
- Dec 2001
- Posts
- 9,502
- Thanks (Given)
- 23
- Thanks (Received)
- 271
- Likes (Given)
- 191
- Likes (Received)
- 1976
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
What boat is it going on? I have props if you need......
-
03-06-2018, 07:34 PM #5Junior Member
- Join Date
- Mar 2018
- Location
- Kaiapoi, New Zealand
- Posts
- 8
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I have some props, but I will keep you in mind if I need one. Cheers
-
03-06-2018, 09:44 PM #6
Cool! Pics of motor?
'71 Glastron V153 - Composite rebuild - Unceremoniously wrecked
'81 Baja 15 SS - "nine-paged" '77 140
'81 Carlson C500 Metric - Currently in foster care
'70 something Speedcraft - Allison 16R clone - Undergoing restoration
'79 Carlson CVZ 19 - Far back burner
WALK TALL AND CARRY A BIG BILGE PUMP
-
03-08-2018, 07:13 PM #7
Take the box off, remove both plugs and stand the box on its drive shaft end. To refill, refit box and with the drive trimmed level refill through the lowest hole until oil runs out the other.
Popey
-
03-10-2018, 11:51 AM #8Screaming And Flying!
- Join Date
- Dec 2001
- Posts
- 9,502
- Thanks (Given)
- 23
- Thanks (Received)
- 271
- Likes (Given)
- 191
- Likes (Received)
- 1976
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
What if time is short? And you can't pull lower.
Similar Threads
-
Photos: Evinrude Super Strangler!
By Scream And Fly in forum General Boating DiscussionReplies: 248Last Post: 10-15-2019, 12:42 PM -
Evinrude Super Strangler? Racing Motor in Minneapolis!
By ChinewalkerII in forum Outboard and Racing HistoryReplies: 8Last Post: 04-28-2013, 07:59 AM -
Evinrude Super Strangler V4 - 4 Page Catalog
By Scream And Fly in forum Outboard and Racing HistoryReplies: 46Last Post: 02-20-2007, 11:43 AM -
Twister 2 or Super Strangler
By KG4 in forum General Boating DiscussionReplies: 15Last Post: 08-04-2002, 07:59 PM