User Tag List
Thanks: 0
Results 31 to 33 of 33
-
04-10-2018, 07:54 AM #31Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,753
- Thanks (Given)
- 381
- Thanks (Received)
- 1302
- Likes (Given)
- 5601
- Likes (Received)
- 11031
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
Veil mat is a very fine, very tightly compressed long strand material used mainly for a skin coat . It has no print pattern and is very thin. The thinnest glass there is I believe. I have used it on chemical tanks when I built water treatment systems. And on a few molds.
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
-
04-24-2018, 01:28 AM #32when your not bagging do you have any tips on doing inside corners?
-
04-24-2018, 06:31 AM #33Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,753
- Thanks (Given)
- 381
- Thanks (Received)
- 1302
- Likes (Given)
- 5601
- Likes (Received)
- 11031
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
Depends on the material. If using a knitted or woven glass you will have to cut the glass to allow it to fold and overlap. Also helps to push the glass into the corner and wet it out before placing the next piece. Covering with a torn piece of mat will help it all to stay in place and makes it stronger. If just using mat, wet it out, wait a few mins and stretch it some after letting the resin dissolve the binder. A radius roller used to roll the glass INTO the corner will eliminate the air voids. Patience is the key to getting nice corners.
Last edited by XstreamVking; 04-24-2018 at 06:38 AM.
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
Similar Threads
-
Peel ply!!
By tunnels in forum Fiberglass and Composites DiscussionReplies: 19Last Post: 09-28-2016, 03:07 AM -
Everything you ever wanted to know about peel-ply - and much more...
By Dougw in forum Fiberglass and Composites DiscussionReplies: 20Last Post: 01-03-2011, 08:20 AM -
How to 'peel' an egg without peeling!
By ress453 in forum The Scream And Fly LoungeReplies: 3Last Post: 08-06-2008, 10:46 PM -
how to take off orange peel??
By bluecheckmate in forum Fiberglass and Composites DiscussionReplies: 8Last Post: 06-06-2006, 12:17 AM -
To peel or NOT peel horsepower decals??
By Ron V in forum General Boating DiscussionReplies: 2Last Post: 01-29-2005, 08:13 PM