User Tag List
Likes: 0
Results 1 to 12 of 12
-
03-09-2016, 09:16 AM #1Junior Member
- Join Date
- Aug 2008
- Location
- Wisconsin
- Posts
- 7
- Thanks (Given)
- 0
- Thanks (Received)
- 2
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
1986 10' Centurion Tunnel Boat, Evinrude 60 hp short shaft twin, ShoreLand'r trailer
Boat in very good condition with exception of a one stress crack. (I believe someone stepped on top of deck) Does not take away from the looks and strength of boat. Bottom of boat very nice.
Evinrude 1985 60hp block built similar to an sst 45. Short shaft. Engine has not even four hours with a complete rebuild. Runs great. New iridescent paint.
ShoreLand'r boat trailer in excellent condition.
$4800.00/bo
2183935636Last edited by seahorse150; 03-09-2016 at 04:56 PM. Reason: Adding year of boat
-
03-18-2016, 12:05 AM #2
Where are you located in Wisconsin? Any interest in separating the boat and motor?
-
03-18-2016, 07:53 PM #3Junior Member
- Join Date
- Aug 2008
- Location
- Wisconsin
- Posts
- 7
- Thanks (Given)
- 0
- Thanks (Received)
- 2
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Lake Nebagamon, WI. I possibly would. What are you thinking?
-
03-19-2016, 07:31 AM #45000 RPM
- Join Date
- Sep 2012
- Location
- Pennsylvania
- Posts
- 142
- Thanks (Given)
- 28
- Thanks (Received)
- 6
- Likes (Given)
- 22
- Likes (Received)
- 50
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
May we see a photo of the stress crack on the deck ?
If Sulzy is interested in the motor , I'm interested in the hull .
Thx,
Steve S
-
03-19-2016, 10:41 AM #5
Little to far of a drive for me. Thanks for the fast response tho. Good luck with your sale
-
03-21-2016, 03:00 PM #65000 RPM
- Join Date
- Sep 2012
- Location
- Pennsylvania
- Posts
- 142
- Thanks (Given)
- 28
- Thanks (Received)
- 6
- Likes (Given)
- 22
- Likes (Received)
- 50
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I'd still would like to see a photo of the crack in the deck ...
Steve S
-
03-22-2016, 01:35 PM #7Junior Member
- Join Date
- Aug 2008
- Location
- Wisconsin
- Posts
- 7
- Thanks (Given)
- 0
- Thanks (Received)
- 2
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
Steve-S thanked for this post
-
03-22-2016, 02:33 PM #85000 RPM
- Join Date
- Sep 2012
- Location
- Pennsylvania
- Posts
- 142
- Thanks (Given)
- 28
- Thanks (Received)
- 6
- Likes (Given)
- 22
- Likes (Received)
- 50
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I see the starting point , how far toward the dash does it run ?
Is it only at the surface level or all the way through and visiable from the inside ?
Steve
-
03-22-2016, 03:46 PM #9Junior Member
- Join Date
- Aug 2008
- Location
- Wisconsin
- Posts
- 7
- Thanks (Given)
- 0
- Thanks (Received)
- 2
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
It goes about two thirds up. There was a decal over to hide when I bought it years ago. I don't think it is all the way through, although I never could get under the dash to check. It never got any worse. It never bothered me. It is still a real solid deck.
Last edited by seahorse150; 03-22-2016 at 03:49 PM.
-
Steve-S thanked for this post
-
05-06-2016, 09:05 AM #10Junior Member
- Join Date
- Aug 2008
- Location
- Wisconsin
- Posts
- 7
- Thanks (Given)
- 0
- Thanks (Received)
- 2
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
$4600.00/ bo
-
05-17-2016, 10:30 AM #11Junior Member
- Join Date
- Aug 2008
- Location
- Wisconsin
- Posts
- 7
- Thanks (Given)
- 0
- Thanks (Received)
- 2
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Best reasonable offer. I don't have use for anymore. You won't be disappointed.
M
-
06-04-2016, 09:42 PM #12Junior Member
- Join Date
- Aug 2008
- Location
- Wisconsin
- Posts
- 7
- Thanks (Given)
- 0
- Thanks (Received)
- 2
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Sold
Similar Threads
-
Engine Height ? on DCB22 with twin Drags short shaft
By dcb22 in forum Props, Setup, and RiggingReplies: 2Last Post: 04-28-2011, 09:32 AM -
evinrude 75hp short shaft
By john rowley in forum Outboard and Racing HistoryReplies: 5Last Post: 05-07-2009, 07:58 PM -
Evinrude 70 short shaft question
By arcticracer in forum Technical DiscussionReplies: 3Last Post: 07-24-2005, 12:54 PM