User Tag List
Results 76 to 90 of 115
-
04-30-2017, 04:51 PM #76
Nice decals.........
-
boatman14544 liked this post
-
05-01-2017, 08:24 AM #77Member
- Join Date
- Oct 2007
- Posts
- 88
- Thanks (Given)
- 1
- Thanks (Received)
- 10
- Likes (Given)
- 31
- Likes (Received)
- 48
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
05-30-2017, 09:21 AM #78Member
- Join Date
- Oct 2007
- Posts
- 88
- Thanks (Given)
- 1
- Thanks (Received)
- 10
- Likes (Given)
- 31
- Likes (Received)
- 48
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
05-30-2017, 03:27 PM #79
-
wogi liked this post
-
05-30-2017, 03:53 PM #80
-
05-30-2017, 07:15 PM #81
need a pair of SSM's now.......
-
boatman14544 liked this post
-
05-31-2017, 10:55 AM #827000 RPM
- Join Date
- Dec 2002
- Location
- South Florida
- Posts
- 2,296
- Thanks (Given)
- 0
- Thanks (Received)
- 155
- Likes (Given)
- 1
- Likes (Received)
- 542
- Mentioned
- 11 Post(s)
- Tagged
- 0 Thread(s)
Paint some big old FJJ numbers down the sides and it's 1968 again.
-
boatman14544, Mark75H liked this post
-
07-10-2017, 09:54 AM #83Member
- Join Date
- Oct 2007
- Posts
- 88
- Thanks (Given)
- 1
- Thanks (Received)
- 10
- Likes (Given)
- 31
- Likes (Received)
- 48
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
427Man liked this post
-
07-10-2017, 10:04 AM #84
1996 Four Winns Unlimited U-19 351 I/O Deep V
1977 HydroStream Viper Merc 1500 XS
1981 Baja 17 Bow Rider Merc 1500
2 Pool Rafts
-
07-10-2017, 10:18 AM #85Member
- Join Date
- Oct 2007
- Posts
- 88
- Thanks (Given)
- 1
- Thanks (Received)
- 10
- Likes (Given)
- 31
- Likes (Received)
- 48
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Darrell, I had to do some horse trading to get it, cost me a bunch of stuff that was laying around. Also picked up a lower with a Bobs cone and LWP on it, but it is long shaft for now. Old powerhead very savable, just scuffed up 2 pistons, didn't run it long enough to do any real damage so I got real lucky. It will be back burnered and become a winter project
1964 Chris Craft Holiday
Homemade Glen-l Crackerbox
71 Switzer 17 with twin Merc 1350s
-
427Man liked this post
-
07-10-2017, 10:41 AM #86Member
- Join Date
- Oct 2007
- Posts
- 88
- Thanks (Given)
- 1
- Thanks (Received)
- 10
- Likes (Given)
- 31
- Likes (Received)
- 48
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
07-10-2017, 10:45 AM #87
-
07-10-2017, 10:56 AM #88Member
- Join Date
- Oct 2007
- Posts
- 88
- Thanks (Given)
- 1
- Thanks (Received)
- 10
- Likes (Given)
- 31
- Likes (Received)
- 48
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
the cables just have the motor ends on them, I screwed then to the inside of the deck in front of my control boxes and just have a piece of tape marking the high and low points. I just line up the ends to be sure the motors are at the same angle is all. It saves me from have to turn around and look all the time.
1964 Chris Craft Holiday
Homemade Glen-l Crackerbox
71 Switzer 17 with twin Merc 1350s
-
07-10-2017, 11:04 AM #89
-
07-10-2017, 11:10 AM #90Member
- Join Date
- Oct 2007
- Posts
- 88
- Thanks (Given)
- 1
- Thanks (Received)
- 10
- Likes (Given)
- 31
- Likes (Received)
- 48
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
nope, just a hose clamp and a screw in the bottom bolt that holds the cover cap. Like I said "Old School"
1964 Chris Craft Holiday
Homemade Glen-l Crackerbox
71 Switzer 17 with twin Merc 1350s
-
427Man liked this post