3 litre wolf efi crankcase injected 3 litre build

**mrcrsr** · 01-09-2013, 06:53 AM

actually thats the old one, pulled it off to use as a template, the new one is already rough cut and sitting in the mill, i'll definetely put more curves in this one. still have to build 2 gearcases for the boat as well

**1 Tuff 69** · 01-09-2013, 08:14 AM

Looking good there charlie !

**Frank Molé** · 01-09-2013, 05:49 PM

looks good,hope to see you in march..................

**mrcrsr** · 01-10-2013, 06:47 AM

definetely frank, don't know if i'm going to make the suwanee, river ranch is april

**mrcrsr** · 01-12-2013, 08:05 AM

here's the new wingplate, made out of 6061 aluminum

**mrcrsr** · 01-12-2013, 08:24 AM

**Liberator*21** · 01-12-2013, 08:30 AM

Looks great with the shine job you put on it......

**Dave Strong** · 01-12-2013, 10:57 AM

Looks Good, polishing was a nice touch.

Dave

**Chaz** · 01-13-2013, 08:19 AM

Yea , datz da eZy part ...... but what about around the edge's ...

**mrcrsr** · 01-13-2013, 08:37 AM

the edges were a pita, did it in the mill and made up a pattern out of thin cardboard that i followed after a taped the cardboard to the wingplate, definetely handy having a mill, wish i had more space so i could get something bigger! hopefully i'll have the boat running today.

**Frank Molé** · 01-13-2013, 09:18 AM

looks ready for the suwanee.....

.........nice job.

**Chaz** · 01-13-2013, 02:40 PM

I was joking about what it takes to make the cut edges look like the factory forged area's ..

No matter how big the shop , it's never big enough. No matter how big the machine, there will always be a part that you just cant grab. And if ya can grab it, ya just cant swing it .. or the table aint long enough to make a full pass ... LOL

**Dave Strong** · 01-13-2013, 05:58 PM

Originally Posted by Chaz

I was joking about what it takes to make the cut edges look like the factory forged area's ..

No matter how big the shop , it's never big enough. No matter how big the machine, there will always be a part that you just cant grab. And if ya can grab it, ya just cant swing it .. or the table aint long enough to make a full pass ... LOL

That is so true.
Also no matter how your boat is, it's never quite enough.

Dave

**Liberator*21** · 01-14-2013, 08:31 AM

Originally Posted by mrcrsr

found that the poppet valve is open at around 4 psi?? i run an external poppet dump in tandem w/ drystacking in the mid, cranked it up and had water coming out of the dump at idle. pulled it apart, the seal looks good in the poppet, so i'll replace the whole assy, maybe the spring is weak or it has the wrong poppet stem, not sure as i bought this stuff all together. i know usually they don't open until 10 psi, the 3 litre is supposed to be regulated to 12 if i remember correctly

Charlie,

Water dribble at idle out of the Poppet in normal with the Simon kit. I had the same issue and spoke to Eric about it and he replied that it was normal to have a small stream coming out at idle.

**mrcrsr** · 01-15-2013, 07:55 AM

here it is fully assembled

User Tag List

Thread: 3 litre wolf efi crankcase injected 3 litre build

Thread Tools

Display

Posting Permissions