User Tag List
Thanks: 0
Likes: 0
Results 1 to 9 of 9
Thread: Bleed lines???
-
12-27-2011, 04:46 PM #1
6000 RPM
- Join Date
- Aug 2006
- Location
- Kingsland GA.
- Posts
- 1,327
- Thanks (Given)
- 0
- Thanks (Received)
- 1
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Bleed lines???
Anybody know where I can by bleed lines or about a 4 foot length of it to redo the bleed lines on my 2.5 200?
Thanks
-
12-27-2011, 05:03 PM #2
Supporting Member
- Join Date
- Oct 2002
- Location
- Dallas, TX
- Posts
- 15,146
- Thanks (Given)
- 29
- Thanks (Received)
- 56
- Likes (Given)
- 377
- Likes (Received)
- 381
- Mentioned
- 1 Post(s)
- Tagged
- 1 Thread(s)
tygon tubing in the lawnmower section of a hardware store.
> Stainless steel Merc cowling plates - $110 shipped TYD - LINK <
1979 16' Action Marine/2.5L Merc S3000 - Metalflake Maniac
1984 18' Contender Tunnel/2.4 Merc Bridgeport
"Where does the love of God go, when the waves turn the minutes to hours?"
-
12-27-2011, 05:41 PM #3
6000 RPM
- Join Date
- Aug 2006
- Location
- Kingsland GA.
- Posts
- 1,327
- Thanks (Given)
- 0
- Thanks (Received)
- 1
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I have check them all around here and no one carries it. Looking for a source nline to order it from. Not sure what size to buy either.
Thanks
-
12-27-2011, 06:58 PM #4
Supporting Member
- Join Date
- Oct 2002
- Location
- Dallas, TX
- Posts
- 15,146
- Thanks (Given)
- 29
- Thanks (Received)
- 56
- Likes (Given)
- 377
- Likes (Received)
- 381
- Mentioned
- 1 Post(s)
- Tagged
- 1 Thread(s)
www.mcmaster.com Tygon PVC is what they call it. I believe bleed lines are 3/32" ID. Measure the barb to be sure.
> Stainless steel Merc cowling plates - $110 shipped TYD - LINK <
1979 16' Action Marine/2.5L Merc S3000 - Metalflake Maniac
1984 18' Contender Tunnel/2.4 Merc Bridgeport
"Where does the love of God go, when the waves turn the minutes to hours?"
-
12-27-2011, 07:12 PM #5
5000 RPM
- Join Date
- Oct 2008
- Location
- Plainville, CT
- Posts
- 804
- Thanks (Given)
- 417
- Thanks (Received)
- 23
- Likes (Given)
- 377
- Likes (Received)
- 67
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I replaced mine with NAPA fuel line part #H174 with good luck. Even with the inside diameter listed at 1/8" they seemed snug; although used ties as a precaution. My impression is that the material for this line is tougher and more heat resistant than the tygon.
-
12-27-2011, 07:26 PM #6
5000 RPM
- Join Date
- Jul 2009
- Location
- spokane
- Posts
- 847
- Thanks (Given)
- 9
- Thanks (Received)
- 6
- Likes (Given)
- 24
- Likes (Received)
- 48
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
3/32 is what you need
-
12-27-2011, 11:01 PM #7
Supporting Member
- Join Date
- Oct 2011
- Location
- ft pierce fl
- Posts
- 1,583
- Thanks (Given)
- 30
- Thanks (Received)
- 41
- Likes (Given)
- 622
- Likes (Received)
- 340
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
boats.net 1-877-408-1499 i just got a 20ft roll and it is small diameter outside like factory and fits tight no need to tie strap.
-
12-30-2011, 09:40 AM #8
Scream And Fly VIP
- Join Date
- Aug 2007
- Location
- North Eastern North Carolina
- Posts
- 8,179
- Thanks (Given)
- 230
- Thanks (Received)
- 344
- Likes (Given)
- 254
- Likes (Received)
- 1352
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
This is where I buy mine from. They will sell in 10 foot lenghts.
http://www.usplastic.com/catalog/ite...3487&catid=579Bud Conner "Heathen" "Defending Our Constitution"
FOR ALL ENGINE APPLICATIONS
DRY Film Lubricant for Piston Skirts & Cranks + Thermal Barrier Ceramic Coatings for Piston Tops, Combustion Chambers, Valves etc !!
-
12-30-2011, 01:00 PM #9
5000 RPM
- Join Date
- Apr 2001
- Location
- Melbourne, Florida
- Posts
- 645
- Thanks (Given)
- 0
- Thanks (Received)
- 5
- Likes (Given)
- 0
- Likes (Received)
- 13
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Ace Hardware carries it also
Reply With Quote
