User Tag List
Thanks: 0
Likes: 0
Results 1 to 7 of 7
Thread: 5250 bottom guided rods
-
09-22-2011, 11:48 PM #1Screaming And Flying!
- Join Date
- Jul 2002
- Location
- FT WORTH, TEXAS
- Posts
- 8,031
- Thanks (Given)
- 9
- Thanks (Received)
- 146
- Likes (Given)
- 313
- Likes (Received)
- 503
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
5250 bottom guided rods
when a machine shop cuts the .050 off each side of these rods so the can be run top guided do the cut the rod journal end also or just wrist pin end
-
09-23-2011, 06:41 AM #2
depends on the rods, merc had a couple of bastard yrs where 1 side was .812 and one was .712, most bottom guided were .812 on both sides, so you would take .050 off both ends on either side. the final measure to convert to top guide is .712 on the small and big ends. jay smith cuts them down now
-
09-24-2011, 12:58 PM #3Screaming And Flying!
- Join Date
- Jul 2002
- Location
- FT WORTH, TEXAS
- Posts
- 8,031
- Thanks (Given)
- 9
- Thanks (Received)
- 146
- Likes (Given)
- 313
- Likes (Received)
- 503
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
thanks for the info
-
09-24-2011, 08:11 PM #4Supporting Vendor
- Join Date
- Apr 2001
- Location
- Brookeland , Texas 75931 North of Jasper
- Posts
- 11,838
- Thanks (Given)
- 4
- Thanks (Received)
- 163
- Likes (Given)
- 11
- Likes (Received)
- 795
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Charlie is RIGHT ON ! Both ends have to be .712" - .710" if I remember without digging out notes..
JayJay @ JSRE
-
09-24-2011, 08:30 PM #5Screaming And Flying!
- Join Date
- Jul 2002
- Location
- FT WORTH, TEXAS
- Posts
- 8,031
- Thanks (Given)
- 9
- Thanks (Received)
- 146
- Likes (Given)
- 313
- Likes (Received)
- 503
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
jay what does it cost
-
09-25-2011, 07:28 AM #6Supporting Vendor
- Join Date
- Apr 2001
- Location
- Brookeland , Texas 75931 North of Jasper
- Posts
- 11,838
- Thanks (Given)
- 4
- Thanks (Received)
- 163
- Likes (Given)
- 11
- Likes (Received)
- 795
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
$150.00 a set
JayJay @ JSRE
-
09-25-2011, 08:11 AM #7Screaming And Flying!
- Join Date
- Jul 2002
- Location
- FT WORTH, TEXAS
- Posts
- 8,031
- Thanks (Given)
- 9
- Thanks (Received)
- 146
- Likes (Given)
- 313
- Likes (Received)
- 503
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Not bad i will sell some of this Bridgeport EFI stuff and send you a set to cut thanks