User Tag List
Thanks: 0
Likes: 0
Results 1 to 6 of 6
Thread: Yamaha Vmax help
-
03-11-2010, 08:03 PM #1
Member
- Join Date
- Jan 2009
- Location
- Kingwood TX
- Posts
- 42
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Yamaha Vmax help
I've got an 06 250 hpdi. Went out and ran the boat about 1/2 mile never about about 3000.. Put the it in neutral and it died. It will fire but will not run, I noticed that my alarm is also not working now. I checked wiring connections and found nothing. Ran fine last week.
Thanks for any help..
-
03-11-2010, 08:45 PM #2
AKA Eroshibend Yamamoto
- Join Date
- Apr 2004
- Location
- Long Island
- Posts
- 4,873
- Thanks (Given)
- 15
- Thanks (Received)
- 49
- Likes (Given)
- 957
- Likes (Received)
- 1232
- Mentioned
- 1 Post(s)
- Tagged
- 1 Thread(s)
Sounds like you fowled a plug,make sure you gap them evenly it make a difference
21 SuperBoat VF200 Yamaha SHO
Bender Clan member
Eroshibend Yamamoto
2015 King of the Cut
2016 King of the Cut
2017 King of the Cut💪
-
03-11-2010, 11:24 PM #3
7000 RPM
- Join Date
- Sep 2002
- Location
- Lakeland,Fla
- Posts
- 2,500
- Thanks (Given)
- 0
- Thanks (Received)
- 1
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Check the plugs first then check your fuel. Many times if you have a fuel pres issues they will just keep starting then stall. Even if your horn isnt working you will still have limited RPMs if you over heat or run low on oil.
Fellow G-Man of the Sunshine Syndicate-Dixie Wrecked Chaptor..
We Put The F. U. in FUN
94 17MA Maverick 115 Yamaha
2006 Mustang GT, with a belt driven air cleaner
-
03-12-2010, 08:46 AM #4
5000 RPM
- Join Date
- Dec 2005
- Location
- Valrico Fl.
- Posts
- 564
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 3
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
The king of Yamaha's on this forum is Ray Neudecker ,( Nathan Worthy also would take time to try and help but I have not heard from him in years anyone know where he went?)there is also a new kid on the forum (mcyama)-Martin- both have givin help in the past and both have(yamaha parts) and years of Yamaha experience . I would try and contact one of them and see if they can steer you in the correct direction. Joe R QUOTE=squirrely;1923215]I've got an 06 250 hpdi. Went out and ran the boat about 1/2 mile never about about 3000.. Put the it in neutral and it died. It will fire but will not run, I noticed that my alarm is also not working now. I checked wiring connections and found nothing. Ran fine last week.
Thanks for any help..[/QUOTE]Last edited by Dingie 2; 03-12-2010 at 08:49 AM.
-
03-12-2010, 05:53 PM #5
Banned
- Join Date
- Aug 2009
- Location
- new iberia la.
- Posts
- 336
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
try to verify that the yellow wire in the main harness is not broken or corroded. salty corrision will carry voltage however it will not carry amps. Check at the end of the line at ecu. Thanks Martin
-
03-12-2010, 09:15 PM #6
5000 RPM
- Join Date
- Aug 2008
- Location
- Toronto
- Posts
- 117
- Thanks (Given)
- 1
- Thanks (Received)
- 1
- Likes (Given)
- 1
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I have heard these HPDI's like Seafoam. Keeps the plugs clean and filters clean too!
Reply With Quote
