User Tag List
Thanks: 0
Likes: 0
Results 1 to 15 of 29
-
02-07-2009, 03:43 PM #1
Painting the whole inside... what grit?
hey guys.. this is probably a stupid question but how fine do i need to go on the inside of my boat before i paint it? im not looking for showroom quality, just something that doesnt look like dog s--- ... i also may do a splatter paint on it as well..
i was thinking 180grit is enough....?
scott"If everything's under control, you're going too slow"
-Mario Andretti-
76 vixen,.. on the back burner
82 laser comp. 380 ray
PICS OF THE VIXEN REBUILD
-
02-07-2009, 03:45 PM #2
single stage? 220, but if you are using a D/A you might be able to get away with 180.
> Stainless steel Merc cowling plates - $110 shipped TYD - LINK <
1979 16' Action Marine/2.5L Merc S3000 - Metalflake Maniac
1984 18' Contender Tunnel/2.4 Merc Bridgeport
"Where does the love of God go, when the waves turn the minutes to hours?"
-
02-07-2009, 04:23 PM #3
Im using a DA. and I'm painting it with Imron white (maybe blue/grey or blue/silver splatter)
im painting it on with a brush not spray gun, so that should leave it a little thicker too right?"If everything's under control, you're going too slow"
-Mario Andretti-
76 vixen,.. on the back burner
82 laser comp. 380 ray
PICS OF THE VIXEN REBUILD
-
02-07-2009, 05:19 PM #4
If you're going to use a brush 180 should be fine. Then sometime next year when it gets done you can show us some pictures.
Ló fasz racing
Joe Horvath
-
02-07-2009, 05:53 PM #5
hopefully sooner then next year, im going to do more sanding on it tommorow i think.... been busy lately but every week i have worked on it a little more.
scott"If everything's under control, you're going too slow"
-Mario Andretti-
76 vixen,.. on the back burner
82 laser comp. 380 ray
PICS OF THE VIXEN REBUILD
-
02-07-2009, 07:20 PM #6> Stainless steel Merc cowling plates - $110 shipped TYD - LINK <
1979 16' Action Marine/2.5L Merc S3000 - Metalflake Maniac
1984 18' Contender Tunnel/2.4 Merc Bridgeport
"Where does the love of God go, when the waves turn the minutes to hours?"
-
02-10-2009, 12:57 PM #7
Use Gelcoat. It'll stand up better, may even be cheaper. roll or brush it on..
Jeffhttp://www.powercatboat.com/Group/JBowman/JBowman.html
A Member in good standing of Dicksmarine, Mesa AZ. "The Land of Misfit Toys"
-
02-10-2009, 01:51 PM #8
I vote for gel too.
It's thicker. You can finish it with only one layer. You can apply it real thick.
It's also very strong and you will not have any trouble with pin holes. If you use paint and there are pin holes you will still see them...
-
02-10-2009, 04:23 PM #9
theres already a layer of paint down on the boat from the last time i painted it (nason paint). i dont think the gelcoat will bond correctly to it..?
scott"If everything's under control, you're going too slow"
-Mario Andretti-
76 vixen,.. on the back burner
82 laser comp. 380 ray
PICS OF THE VIXEN REBUILD
-
02-10-2009, 04:34 PM #10
I am as pro-gel as a guy can get, but...
Gel sucks in the interior. it fades easily, it instantly soaks up any amount of dirt/oil and stains, its hard to clean, and durability is a non-issue on the inside of a boat. My whole boat is finished in gel/webbing on the inside, and I'm going to a single stage paint for just those reasons. the only place I'm not painting is directly above the concave pad. water has a small place to sit under the bilge pump and it might blister paint there.
I wouldnt trust gel shot over paint either, although it has been done.> Stainless steel Merc cowling plates - $110 shipped TYD - LINK <
1979 16' Action Marine/2.5L Merc S3000 - Metalflake Maniac
1984 18' Contender Tunnel/2.4 Merc Bridgeport
"Where does the love of God go, when the waves turn the minutes to hours?"
-
02-12-2009, 08:28 PM #11
looks like paint it is! im going to do 100 then 180 with a DA..
i'll post pics whenever its done haha"If everything's under control, you're going too slow"
-Mario Andretti-
76 vixen,.. on the back burner
82 laser comp. 380 ray
PICS OF THE VIXEN REBUILD
-
02-12-2009, 08:46 PM #12
Half of the members that viewed this thread will be dead & gone by the time it's done
Ló fasz racing
Joe Horvath
-
02-12-2009, 08:57 PM #13
haha i didnt know you were that old joe? at least live long enough to watch me whoop yo ass in about 700'
btw when are you having a race in plymoth? theres a friend of mine i wana go visit lol
"If everything's under control, you're going too slow"
-Mario Andretti-
76 vixen,.. on the back burner
82 laser comp. 380 ray
PICS OF THE VIXEN REBUILD
-
02-12-2009, 09:04 PM #14
Yo boy, I know you wanna come back to Plymouth so you can walk all over Eastern NC again
The only way you can whoop me in 700' is on foot. Even then it's gonna be iffy
We've got a new site I'm working on a little west of Plymouth that is going to be big fun. And, I think we'll be back in Plymouth soon. That way you & your daddy can come down and play again
Ló fasz racing
Joe Horvath
-
02-12-2009, 09:33 PM #156000 RPM
- Join Date
- Jul 2003
- Location
- Muskoka, Ontario
- Posts
- 1,061
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Scott, I have done both paint and gel on the floor and if I had to do it again I would use paint. Gel is a pain in the ass.
You better have that thing ready and drag it and yourself over to the Rumble this summer.