User Tag List
Results 61 to 75 of 106
-
07-22-2009, 03:36 PM #615000 RPM
- Join Date
- Jun 2006
- Location
- south dakota
- Posts
- 140
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
THANK YOU SO MUCH FOR YOUR PICTURES. I just bought a Vi King and ran is last weekend and was lucky to get back to the trailer befor it sank. When I pulled it out there was over 2 inches of water on top of the floor. Under the boat just inside of the wooden board the boat sits on on the trailer was a hole about 1 1/2 inches and a piect of cloth stuck out funneled water in. The hole is 5 inches in front of the drain hoole and 13 1/2 inches to the starboard side. I drilled a 1/2 inch hole in the floor and hit wood and the part the drill pulled out was wet. I did not go all the way through. Then I drilled a 1/2 inch hole in the hole in the bottom. There has been water sipping out sence last Sunday. From your pictures it looks like I should drill another hole in the transom of rather at the rear of there the step starts about an inch or so above the bottom. Maybe I could get whatever water is in there out that way. Any suggestions would be more that apperciated.
Thanks again
-
07-22-2009, 06:41 PM #62Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,753
- Thanks (Given)
- 381
- Thanks (Received)
- 1305
- Likes (Given)
- 5602
- Likes (Received)
- 11033
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
Over the years Hydrostream built these boats so many different ways, every one is a little different. Take some photos and start a thread and post the pics. With all the glass wizards on here it should be no problem to get the advice and help you need. You are allready on the right path. Gotta be dry to glass it...Grind it out from the outside of the hull and see how extensive the damage is. Hate to say it, but, the boat may need the floor pulled up to be able to check the core and stringers. And also to glass the backside of the damaged area..
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
-
07-22-2009, 08:26 PM #635000 RPM
- Join Date
- Jun 2006
- Location
- south dakota
- Posts
- 140
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
the seller of my boat said the wood had been replaced. I can't tell if it has. Do you think it would be ok to drill a hole in the bottom of the front of the area where the drain plug is? I tapped with a nhammer and I did notice ad ares from the holw back 5 inches to the tail of the bosy the rest sounded ok.
I got to run it for about 30 munites and I just love this boat. It is a pure hot rod and it screams.
-
07-22-2009, 09:12 PM #64
WoW! That thing looks great! Cant wait to see more pictures as it gets fiunished. The more I see the splashwells decked over the more I am thinking of decking the one on my Vulture.
-Kevin
Project Vulture | Project Vector | Project Vamp | Project CobraJet
1977 Hydrostream Vulture - Worlds longest ongoing project.
1982 Hydrostream Vector
1982 Hydrostream Vamp
1973 Hydrostream Vixen
1976 CobraJet Jet Boat - Outboard conversion project
199? Glastron - aka Boat Anchor
1976 Pontoon - aka The Family Truckster
-
07-23-2009, 06:34 AM #65Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,753
- Thanks (Given)
- 381
- Thanks (Received)
- 1305
- Likes (Given)
- 5602
- Likes (Received)
- 11033
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
Primerate- It may be possible to lower the nose of the boat to allow the trapped water to drain foreward. Once drained from the rear, the water should go to the keel area.and then drain out the existing drain hole...Really need some pics to see what yer working on.
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
-
07-23-2009, 06:44 AM #665000 RPM
- Join Date
- Jun 2006
- Location
- south dakota
- Posts
- 140
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Thanks
I will do that today and take sone pictures and post them tonight
-
07-23-2009, 06:44 AM #67Go boating,be happy!! And wear safety vest please!! And lesson good music...https://www.youtube.com/watch?v=2c5oHITTI8c
-
07-23-2009, 06:46 AM #685000 RPM
- Join Date
- Jun 2006
- Location
- south dakota
- Posts
- 140
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
How do you post pics here??
-
07-23-2009, 06:47 AM #69
Do with:
http://www.tinypic.com/Go boating,be happy!! And wear safety vest please!! And lesson good music...https://www.youtube.com/watch?v=2c5oHITTI8c
-
07-23-2009, 06:53 AM #70Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,753
- Thanks (Given)
- 381
- Thanks (Received)
- 1305
- Likes (Given)
- 5602
- Likes (Received)
- 11033
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
Hippie.. Thanks for the good words. After painting this design, i'm not really all that satisfied with the way it looks. Its hard to have a really original design. I was trying to put some muscle car looks on a boat. After all the parts are installed, it may look better. Windshield really helped to bring it together. If it runs out as expected, it won't matter what it looks like anyway....At 90- 100 mph little things like paint all become very unimportant. Keep working on yours, and it will eventuall get done. The rear deck is definately an improvement over the original splashwell.
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
-
07-23-2009, 07:25 AM #71Go boating,be happy!! And wear safety vest please!! And lesson good music...https://www.youtube.com/watch?v=2c5oHITTI8c
-
07-23-2009, 07:42 AM #72
-
07-23-2009, 08:00 AM #73Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,753
- Thanks (Given)
- 381
- Thanks (Received)
- 1305
- Likes (Given)
- 5602
- Likes (Received)
- 11033
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
Thanks, J.P. It looks good to me also. I'm just one of the nuts that second guesses all decisions that have been made.. It really comes down to the individual persons likes and dislikes. I had some more intricate paint ideas and kind of decided that it was time to get some paint on it and get on the water. Been working on this boat on and off for several years. It's solid and will last forever. The paint job will do for now... Just wanted to have a boat that is different than all the others...I just don't look at it and say WOW! On it's first trip, when I run it to wot, then i'll be saying WOW, this is one fast stream! These boats are really just a thrill ride, on the water..
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
-
07-23-2009, 08:03 AM #74Go boating,be happy!! And wear safety vest please!! And lesson good music...https://www.youtube.com/watch?v=2c5oHITTI8c
-
07-23-2009, 08:08 AM #755000 RPM
- Join Date
- Jun 2006
- Location
- south dakota
- Posts
- 140
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Thats just beautiful
WOW what a nice job. I wish I had that ability great looking