User Tag List
Thanks: 0
Likes: 0
Results 31 to 38 of 38
Thread: Painting MADEFI MIDS????
-
11-02-2006, 02:31 PM #31
steve
what is alodined ??
2005 TRIAD STV EURO
421 HP OMC 3.3 EFI by STOKER
16" Taylor mid, Merc sporty
-
11-02-2006, 03:00 PM #32
Its
the gold colored coating that Merc uses on all the blocks etc. Not anodizing, alodining in case there is confusion. It helps paint adhere better and protects against corrosion.
-
11-02-2006, 03:24 PM #33
Zinc chromate etching primer is the only primer I know that will stay on aluminum.It is that lovely military green color.
-
11-02-2006, 03:42 PM #34
We're not talking primer
Alodining is not primer. Primer goes on over top, then paint. Google it.
-
11-02-2006, 03:49 PM #355000 RPM
- Join Date
- Aug 2002
- Location
- florida
- Posts
- 804
- Thanks (Given)
- 3
- Thanks (Received)
- 4
- Likes (Given)
- 3
- Likes (Received)
- 13
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I HAVE DONE SEVERAL OF wAYNES MIDS AND THEY ARE RUNNING IN SALT WATER. sOME ARE THREE-FOUR YEARS OLD. ZINC CHROMATE. OMNI EPOXY PRIMER THEN PPG CONCEPT. WORKS GREAT
-
11-02-2006, 10:28 PM #365000 RPM
- Join Date
- Dec 2002
- Location
- long island new york
- Posts
- 361
- Thanks (Given)
- 4
- Thanks (Received)
- 0
- Likes (Given)
- 2
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
power coat is junk
paint is the way to go, use the correct primer.....i has a few mids done, rainbow powercoating deerpark new york, and tried colorlife in hicksville new york and both places blow.....never never again...it got me so pist i sold the boat.....
-
11-03-2006, 12:21 AM #37
powder coat
well it sounds like Wayne was right. If you do it wrong it will just peel !!! IT HAS TO BE DONE RIGHT WITH THE RIGHT PRODUCTS !! just like ultrafast stated. There is a right way, and a wrong way.
Lance2005 TRIAD STV EURO
421 HP OMC 3.3 EFI by STOKER
16" Taylor mid, Merc sporty
-
01-05-2007, 02:39 AM #38
I've powdercoated lots of stuff for immersion service in saltwater, work for the navy. If done correctly the stuff is bullet proof. But, if its going to see high temps make sure you got the right stuff. Paint can be chipped just as easy as powder. If it peels off like wall paper then you should go get a refund from the guy who powdered it. If the powder chips repair it the same way you would a paint chip. Lightly scuff (feather) the prime and paint it. It ain't gonna hurt the powder with a little spot of paint and yes paint will stick to it. The key is prepperation just like paint. Ya gotta use the correct media to blast the peices with. Aluminum oxide don't leave a residue (surface contamination) then ya take some xylene and spray it on with a squirt bottle and blow it off with air nozzle till its dry. Then you end up with the cleanest peice of metal and just begg'in for some powder. You can heat it and shoot it hot for a thicker coat or let the electricity do the work and shoot it cold then heat it. But, if not done right it can end up being really brittle. good luck
Last edited by K-Dawg; 01-05-2007 at 02:49 AM.