I just got back from plowin the 1 to 3 they said was commin that ended up more like 9!!!! Yup I've had more than enough!!!!!!!!!!!!!!!!!!!!!!!!!Quote:
Originally Posted by mrichartz
Gonna watch the race and pass out.
Gary
Printable View
I just got back from plowin the 1 to 3 they said was commin that ended up more like 9!!!! Yup I've had more than enough!!!!!!!!!!!!!!!!!!!!!!!!!Quote:
Originally Posted by mrichartz
Gonna watch the race and pass out.
Gary
Go jimmy #48
BTW Ken I got a chance to get back at the Viper and gonna post some more pics on my thread tonight or tomorrow....Just about done, I can taste it!!!Quote:
Originally Posted by racervboat
Gary
Doe's it taste like chicken ? haha Just pm'd you gary.
Well finally got the bobs solid mounts yesterday and got the mid together.The trim im going to use is the same set-up that's on the v-4 as seen on my thread rebirth of an 12 inch omc mid.I will save the offshore single ram and cut it down for the mid if I get another boat if it don't work out that well on the 16ft ally.
Also got the new to me 15x32 cleaver from a s&f member it was worked but never polished so I went to town on it.Then I got creative and turned rj's mod powerhead into a helicopter motoa hahaha :cheers:
Looks good, gonna need a lefty for your helicopter. ;-)Quote:
Originally Posted by racervboat
https://www.screamandfly.com/attachm...4&d=1519307799
I was thinking the same think n-p but I could get a left hand starter and spin it backwards the powerhead can run either direction just like a merc?
No its not done yet, but it's getting close ......... should be less that 2 weeks. :thumbsup:
Attachment 400346
Attachment 400347
Attachment 400348
Attachment 400349
Whoa metal flake I like it very nice touch
Just metallic Dan, I'm not that froggy. It came off this > Attachment 400352 Thanx for the kudo'sQuote:
Originally Posted by Dan sos express
Attachment 400353
Some more drinks than work
It appears that you turned racervboat's bench on it's side? :thumbsup:Quote:
Originally Posted by rjdubiel
https://www.screamandfly.com/attachm...1&d=1519307799
Lookin'Good NP!!!
Attachment 400364Attachment 400365 How about next years project? This sweet little "72" Checkmate MX-13 followed me home as I just couldn't pass it up. Found me a 15" 75 OMC with the nitro gearcase for her also!!!! Gonna do a complete rebuild of both and my plan is to keep her on the dock and use her to go to work ( houses I have ahead of me to build on the lake)
during three seasons as now it became a tax write off. You know like takin your sports car to work! lol
Gary
Looks to be in pretty good shape, 75hp might be a little but will probably get you down the river. ;-)Quote:
Originally Posted by olboatman
33" Scale winter project
Attachment 400368Attachment 400371Attachment 400373
Made some progress on this winter project. Waiting on paint and supplies to arrive. Got all the crash parts. All but 2 are OE Ford parts as some became obsolete.Quote:
Originally Posted by W2F a V-King
I did get the interior pulled to replace the seat belt re-tractors (part of the air bag system) and the drivers and passenger bags replaced, and reprogrammed the SRS control module. This system is back to functional now. This is also the system that cost the most to repair.
While this is apart, thinking about upping the boost 10lbs. And adding a set of long tubes and a cat back free flow exhaust. Hoping to have this truck done in the next month, so I can get back to my V-King :thumbsup: That new to me hood I am going to make those scoops into a cold air induction, with plumbing to the K&N system it already has.
Attachment 400380 Attachment 400382
Turned out to be an easy job, had too thick of fairing compound keeping the tank from seating. Sanded it down and it fits like a glove. Put the first coat of easypoxy today
Winter project still giving back. 15 inches in the past 5 days,it just won't stop im so done with this white chit.
mid winter, after mill, pre hand work
https://www.screamandfly.com/attachm...7&d=1519675808
https://www.screamandfly.com/attachm...8&d=1519675808
That's a big gap to jump across ... did you notice someone stole a hole. ;-)Quote:
Originally Posted by FMP
WOW now I know I'm gettin old.....I had to look TWICE!!!! lol
Gary
sewing all done interior back in,now put the motor's together
Came out nice:thumbsup:Quote:
Originally Posted by eli
Joe
May the force be with you,minus one hole LOLQuote:
Originally Posted by NICE PAIR
Finally buddy showed up with the cowls,skirts jack plate and hotfoot with slide.Now I can make the steering arms.
Also got the gearcase on too.
Time to take this thing off the back burner (4yrs now) Getting ready to do a mild motor upgrade. pull out the 427 and shove it in a corner somewhere and Install the 540. Good luck M21, I hope you can hang in there.
Attachment 400610 Nice job.Quote:
Originally Posted by eli
Nice Project .... who parked that f.o.r.d. in the drive? ;-)Quote:
Originally Posted by Krazymaan
Always look on the bright side, not minus one, rather it's plus one.:thumbsup:Quote:
Originally Posted by racervboat
How did I miss that? :DQuote:
Originally Posted by FMP
Hey now... be nice. That's my air suspensioned 1 ton dually 7.3 yacht hauler. Licensed at 33k. More than a brand new Dodgee Boy.
Fixing this..Attachment 400622
Few areas I will let the sun work out as i do not want to chance heat gun on pvc vinyl and really f something up
Just pullin your chain, you ford guys are easy. :thumbsup:Quote:
Originally Posted by Krazymaan
gettin close ... maybe 2 weeks. ;-)
http://www.performanceboats.com/delt...-repair-3.html
Didn’t you say that umm........two weeks ago.
I really have no place to talk to talk as I’m way behind you in progress on my project.
Some guys would have just stayed in it, that photo could have looked way different.Quote:
Originally Posted by mrichartz