Ran the Rallysport with the new 300R again today

[WILDMAN]

Tried a few more props. 32 Promax ran 90.8 but was on the limiter at 6450 rpm.


https://www.screamandfly.com/attachment.php?attachmentid=495202&d=1635095038



https://www.screamandfly.com/attachment.php?attachmentid=495203&d=1635095038





https://scontent.ftpa1-1.fna.fbcdn.net/v/t39.30808-6/247885154_4985502341477601_5771409908680112908_n.jpg?_nc_cat=105&ccb=1-5&_nc_sid=8bfeb9&_nc_ohc=gjCURNtxmRgAX8jzQOZ&_nc_ht=scontent.ftpa1-1.fna&oh=b2ac52ff0113d1811d8d695530dff607&oe=617AF3A3

[TooStroked]

Tried a few more props. 32 Promax ran 90.8 but was on the limiter at 6450 rpm.


https://www.screamandfly.com/attachment.php?attachmentid=495202&d=1635095038



https://www.screamandfly.com/attachment.php?attachmentid=495203&d=1635095038





https://scontent.ftpa1-1.fna.fbcdn.net/v/t39.30808-6/247885154_4985502341477601_5771409908680112908_n.jpg?_nc_cat=105&ccb=1-5&_nc_sid=8bfeb9&_nc_ohc=gjCURNtxmRgAX8jzQOZ&_nc_ht=scontent.ftpa1-1.fna&oh=b2ac52ff0113d1811d8d695530dff607&oe=617AF3A3
Randy,

How did the boat (and you) like the Pro Max? I'm struggling with props for my Progression 22 with a 250R and the 30" Pro Max sounds like it might be the ticket.

[WILDMAN]

If you don't jack the motor at least 1" above the bottom, it will be a bitch to drive

[RADER]

Nice

[JBS]

That's impressive pushing that heavy boat that fast. How does that compare with the other motors that were on that boat? Just curious but how does that single axle trailer pull?

[WILDMAN]

Accelerates much better than any other motor. This is the first new boat I ever bought bare and rigged and painted myself. That was in 2000. The single axel tows perfect and is easier to move around when unhooked. I was on a budget back then, so it's not as fancy as I use now.

[TooStroked]

If you don't jack the motor at least 1" above the bottom, it will be a bitch to drive
That's kind of the problem (a bitch to drive) I have now with a Bblades Blaster. I can't go any higher than this and still get water to the motor.


https://hosting.photobucket.com/images/e60/tfwarda/IMG_2327_1_.JPG

[CUDA]

Square aluminum tubing 3x3 thick wall, add offset raise motor;)


That's a very narrow pad flip it over make it 10 10.5 inches:cheers:

It will be a lot easer to drive and faster

[JBS]

I wonder how that 300r would run on those 21 and 24 checkmates you used to sell?

[WILDMAN]

That should be fine. Run it as high as water pressure will allow. I don't have tabs and chinewalk is not a problem as long as you get the motor high. If you run it too low, the chinewalk will be crazy!


That's kind of the problem (a bitch to drive) I have now with a Bblades Blaster. I can't go any higher than this and still get water to the motor.


https://hosting.photobucket.com/images/e60/tfwarda/IMG_2327_1_.JPG

[WILDMAN]

The 300XS would always hit the limiter at 96 with a 28 Trophy. I ran a 30 Promax once and hit 98.4, but it took a while to get there. I'm sure the 300R would run 100 with the same setup.


I wonder how that 300r would run on those 21 and 24 checkmates you used to sell?

[2.5-21]

Gotta remember those Sportys are much larger in diameter than the 3.0 uses. I did see a set of 300 Verados for sale that had 3.0 sportys on them.
Randy.... How much water pressure you see at speed?

[WILDMAN]

I was running 10-12. Could have gone a little higher but I was already on the limiter at 6450

[2.5-21]

What PSI will it guardian?

[WILDMAN]

Usually 7-8, but the temp horn kicks in first at 185-190

[2.5-21]

http://cdn.shopify.com/s/files/1/1061/1924/products/Thumbs_Up_Hand_Sign_Emoji_grande.png?v=1571606063

[Ziemer]

I was running 10-12. Could have gone a little higher but I was already on the limiter at 6450

These motors don't seem to run much water pressure. Mine rarely gets above 12-13 psi at any speed (or height) and usually is between 10-12.

[WILDMAN]

When I lower the motor 1/2", it has 30 lbs of water pressure.