Mercury 2.4/2.5 V6 parts FS 80's/90's-clearing out good stock used parts

[centuryclub1990]

Mercury 2.5-2.4-2L V6 carb and EFI Hi-Po PARTS REDUCED PRICING JAN '19

REDUCED for quick sale-----I'm clearing out all my remaining used MERCURY parts Please PM me with your email info/# and I can send pics
2.5 PARTS
-small top(1.5") crank stator carrier cap w/brg -$80
-sets switch boxes-$150/set (Hi-Po #7778-A2--9.6 Ohm)
-lower unit prop-shaft 1.190" OD brg journal- $75
-9 and 8 tooth starters $100 ea
-good used 2,5 260HP pistons-1 set 6 pistons (side Pin) w/o rods $275 or $50ea

2.4 MERCURY Carb/ EFI and BP parts for sale
-Stator Top Brg crank cap w/brg HP $80ea
-V^ Merc 2L/2.4L crank (oiler) $250
-HD 5250 rods $120 set or 30 ea
-Hi-Po V6 switch boxes $150 set (Hi-Po #7778-A2 - 9.6Ohms)
- 2x 8000 RPM limiters ($50 ea), wiring harness assembles $35
-One set ‘90’s-V6 (200HP) electrics with coils/wiring $175 (Hi-O/P 40 amp) also have 14ohm electrics w/wiring, trigger and stator+40amp +flywheel $350 --complete system $400
-RODS HD set(s) BP EFI/Mod VP #625-5250-$20ea......also 6 shot peened -$40 ea
-1.87 stock '90's Big Brg Lower unit (housing only 200HP) PN 1647-9147 v-good shape $200 little use as gutted gears to install in CLE unit I repaired.
-2.4 Lower Unit 1:87 prop shaft -1.190" OD brg journal-$85
-200 HP stock used pistons w/rods or single port/star-board -Set/w/rods $150 or each w/o rod $25-One new .020” over stock piston w/rings $100
-Complete 200HP 1990 - 1991 stock 1 pc hood (Main + 2 lower underside side bases) $175
-New V6 engine harness engine to dash Key $90
-stock flywheels $75, 8 & 10 tooth starter $75, misc electrical parts-eng wiring
2.0 Ltr 150XS PARTS-
-set head gaskets #27-18785-1 $25/set (150HP)

NOTE-handling/shipping extra-Pricing in USD$
:thumbsup:

[texasvector]

pm sent

[Nielmcque]

What carbs are they and do you have picture of the one piece hood and parts

[centuryclub1990]

What carbs are they and do you have picture of the one piece hood and parts

The Hood and lower halves and carbs are off '91 Merc 200HP--PM me and I'll give you my email to send pics
Robb

[gambler ss]

I'm looking for a one piece exhaust plate or a two piece with solid motor mounts for a 2.4 mercury outboard also need brass bushings all the parts that slide on the shaft that pivots the motor for steering ,sorry about the lack of technical term.
Thanks Floyd

[centuryclub1990]

I'm looking for a one piece exhaust plate or a two piece with solid motor mounts for a 2.4 mercury outboard also need brass bushings all the parts that slide on the shaft that pivots the motor for steering ,sorry about the lack of technical term.
Thanks Floyd

Sorry only have whats on the list.
RT

[pappa pete]

Is the lower a big bearing ratcheting case

[centuryclub1990]

Is the lower a big bearing ratcheting case

Not sure what you mean---all I have is a emptyt gearcase 1:86 off '90's V6 Merc 200

[pappa pete]

What's the casting number on top of lower unit

[pappa pete]

I'd for high performance lower and preferred 200 case

[pappa pete]

1647-9147 1647-9147C 1647-9147C-1 are all big bearing ratcheting case, C2, C3,C4 are small bearing cases.which aren't linked for hp applications

[centuryclub1990]

1647-9147 1647-9147C 1647-9147C-1 are all big bearing ratcheting case, C2, C3,C4 are small bearing cases.which aren't linked for hp applications

Ok its a 1647-9147 in excellent shape; little use as we gutted it to use gears for a CLE case. All paint original.

[gambler ss]

I found a exhaust adaptor plate on ebay thanks for your repley

[sk844]

Pm sent

[snicrep]

do you have the stator? Do i understand that it is $80? Let me know. I need it for an 86 2.4. thanks

[Troubledman]

Is the #46 carb setup and boysen duel reeds still available?

[Troubledman]

Is the #46 carb and manifold setup with the boysen duel reeds still available?