3.6 GT Evinrude V8

[BOATMANBLUES]

Here is a 86 3.6 v8..v8 gearcase with nosecone..got in a trade off a running rig..took it apart for a look ..all standard bore..
rings coked up a bit..just cleaned up the lands and re-ringed it..have not rigged it on anything to run it since..
Got a cool nitrous fogger on it if your into that..bottle comes with it..$3500
Can text me ..843 259 4518..i rarely answer the phone.. thanks for checking it out

[Cat32]

Would you sell just powerhead?

[BOATMANBLUES]

No..want to sell it complete..

[magnum2.5]

these V/8's are comming back, nostalgic, nitrous, gas burner...very cool...building a custom 23' cat with a 4 ltr V/8...in progress...like WILDMAN say's "it's not how fast you go it's how COOL you look"

[BOATMANBLUES]

thats what it's all about..they do look cool...no billet..no anodize..no digital bs..just smokey gas guzzlin torque monster two strokes...
like god intended outboards to be..good luck with your cat

[OBT100]

thats what it's all about..they do look cool...no billet..no anodize..no digital bs..just smokey gas guzzlin torque monster two strokes...
like god intended outboards to be..

Amen to that:iagree:

That outboard is amazing! Id have that in a second if I wasnt in Australia!
Good luck with the sale on a mint looking motor.

[Smoking Joe]

Amen to that:iagree:

That outboard is amazing! Id have that in a second if I wasnt in Australia!
Good luck with the sale on a mint looking motor.

Mate, just get it crated and share a container. Do the math, you might be pleasantly surprised. ;)

V8 two stroke, no more cool than these.

[OBT100]

Preaching to the converted haha, im already restoring two of them.:)

[Da Bull]

Sure it`s a gas drinker but at $3500 vrs $18k for a new 300XS=$14,500 for gas. Thats a lot of gas!

[magnum2.5]

at $3500 + a$3500 for a MONTY powerhead = $7000 for a 400hp fire breathing monster still cheaper than a used 300x with no warranty...and you get the WOW factor for free....

[Smoking Joe]

My fire breathing, fully rebuilt (open chequebook rebuild) and modded monster @400hp (not dynoed) owes me in total $NZ14,500. This was build by NZs equivalent to Monty. This cost includes engine purchase etc etc, is a total cost. And I am still to blow smoke through this engine. I never new I possessed such patients.....:eek:

[powerabout]

what mods did you get Joe?

[Smoking Joe]

what mods did you get Joe?

From what I could remember and wrote down.

Wisco pistons.
Block bored and decked.
Ports modified as per Etec ports, finger ported and port matched. Porting included the removal of port bridges.
Carburettor plennem replaced with one off 3.6 litre.
25 inch mid spliced with 20 inch Offshore mid to give 25 inch offshore mid with offshore exhaust.
Exhaust tuner modified to give better exhaust breathing and venting via offshore snout.
Engine bracket/trim/tilt changed for faster, stronger late model one.
Gearbox changed to last of model box. Internally the box is like new. Owen replaced shaft seals.
Reeds changed.
Gearbox has new waterpump and shaft seals.

I understand that there was some other "stuff" which I am not privy to.

Still yet to be started!!!!!!! :leaving:

[powerabout]

What rpm have those mods been aimed at

[Rum&Coke]

I have a twin pair of Evinrude 3.6 300hp V8's for sale as well. 291 original hours. Feel free to make a reasonable offer. Just bought the boat and repowering. http://miami.craigslist.org/mdc/bpo/4892250591.html

[Smoking Joe]

What rpm have those mods been aimed at

I believe I still have the original factory limiter on this engine because it is going on a larger, heavier boat.

[Isecube22]

Here is a 86 3.6 v8..v8 gearcase with nosecone..got in a trade off a running rig..took it apart for a look ..all standard bore..
rings coked up a bit..just cleaned up the lands and re-ringed it..have not rigged it on anything to run it since..
Got a cool nitrous fogger on it if your into that..bottle comes with it..$3500
Can text me ..843 259 4518..i rarely answer the phone.. thanks for checking it out


Any of these engines on this post still avaliable

[JohnP88]

i have a 3.6 evinrude for sale in nh. has been sitting for a few years, but ran strong when we took it off

[Isecube22]

i have a 3.6 evinrude for sale in nh. has been sitting for a few years, but ran strong when we took it off

How much jus commited to a 4 liter 4 hours away I really just need a crank

[baassoc]

Do you have any pic's?

[JohnP88]

How much jus commited to a 4 liter 4 hours away I really just need a crank
1200

[baassoc]

What year? 85 86?

[JohnP88]

What year? 85 86?
1985

[baassoc]

Sent you PM

[STV_Keith]

My fire breathing, fully rebuilt (open chequebook rebuild) and modded monster @400hp (not dynoed) owes me in total $NZ14,500. This was build by NZs equivalent to Monty. This cost includes engine purchase etc etc, is a total cost. And I am still to blow smoke through this engine. I never new I possessed such patients.....:eek:

You can have a pair of Monty motors with CLE's for $10k! Each one was 380+hp on Monty's dyno.
https://www.screamandfly.com/showthread.php?318652-FS-Pair-of-Monty-Racing-V8-s-25-quot-offshore-mids-w-CLE-lowers

[Haynessey]

i have a 3.6 evinrude for sale in nh. has been sitting for a few years, but ran strong when we took it off

Any pictures of this motor? PM Sent...