PDA

View Full Version : 2.5 200hp cle lower



APACHEKID
12-09-2014, 10:02 PM
Motor is a 2.5 200hp black max with alien cowling motor is fresh about 50hrs on has cle lower 1:87 gears drilled exhaust gears in lower are brand new maybe 2 runs on it motor is turn key has good compression on all cyl has thicker gasket on heads to boost up compr has oil injection block off motor spins 28 chopper at 6300rpm all day long will send pics and open to trades looking to go bigger hp can email pics motor has single ram pump motor 20inch mid cle lower and 28 chopper 4300 obo located in south fl

APACHEKID
12-11-2014, 04:59 PM
Tttttttt

APACHEKID
12-12-2014, 10:04 AM
311173311174311173311175311176311177

APACHEKID
12-12-2014, 11:53 AM
Motor is turn key comes with 28 chopper

Despicablekitty37
12-15-2014, 10:08 PM
Motor is turn key comes with 28 chopper

Hi is motor still for sale

mastertrax
12-16-2014, 02:48 AM
That sure looks like a 2.4 with 2 piece heads.

laserguy
12-16-2014, 10:01 AM
Looks like a 2 liter vertical reed non finger ported 150 or possibly a 175 - definitely not a bottom feeder 2.5 - anyway good luck with your sale

APACHEKID
12-16-2014, 10:14 AM
Yes motor still for sale

APACHEKID
12-16-2014, 10:17 AM
Pretty sure its a 2.5 200hp been looked at by several ppl who are mechanics and guys in the bussiness and they all say its a 2.5 200hp older block just ros

dagodiver
12-16-2014, 12:09 PM
That is the same motor i run on my T3.
I have never seen port side transfer casting bumps on a 2.5
I can clearly see them in your picture.
I believe that to be a 2.4

Dago

APACHEKID
12-16-2014, 02:17 PM
U talkin about that fishin motor that sounds like a 280

dagodiver
12-16-2014, 02:30 PM
U talkin about that fishin motor that sounds like a 280

LOL i get that a lot.
Ill take a pic for you.
Seriously im running an early 80's stock 2.4 with just over a trillion hours on it.
front half is an older updraft case injection setup.
I can spin a 34" cleaver over 7k with this setup.
Hull weight is #486 according to JB.

Dago

APACHEKID
12-19-2014, 09:02 AM
New price 3000 no lower

Jamesgt727
12-20-2014, 04:33 PM
Send me an email, I'm interested

jamesgt727@yahoo.com

accelarationstation
12-20-2014, 05:13 PM
xr2 ?

APACHEKID
12-22-2014, 12:55 AM
Manyjr@live.com

APACHEKID
12-22-2014, 05:39 PM
Email sent

APACHEKID
12-26-2014, 12:04 PM
3700 with cle lower

johnmiffco
12-26-2014, 01:37 PM
yep,,,
vertical reed 1980s cblock with 2 piece heads
can be anything from 135-200 2.0-2.4
definitely not a 2.5

APACHEKID
12-26-2014, 02:08 PM
Just did my own research yes u guys are correct called the guy who build the motor and asked him y the hell would he tell me this motor was 2.5 he was as well lost but motor is very strong has 140compression on all 6cylinders motor is a bad azz lil fishin motor with a cle lower 1:87 gears some one will get a good buy at this price its turn key will give 28 chopper in deal as well sorry again motor is a 2.4 200 hp

APACHEKID
01-03-2015, 04:24 PM
Trying to sell this weekneed her gone 3500 takes it will help with transport in florida

APACHEKID
01-09-2015, 05:12 PM
Bump for a nice motor

APACHEKID
01-27-2015, 11:30 PM
Bump for any reasonable offer motor has to go

APACHEKID
02-16-2015, 09:56 PM
Bump for the week

explorer
05-05-2017, 06:42 PM
Bump for the week
i'll take it. k6343749@yahoo.com

bullet20vee
05-05-2017, 08:22 PM
You're only a little over 2 years late.

explorer
05-05-2017, 08:53 PM
You're only a little over 2 years late.
I'm always late for the good deals

ryan rodriguez
06-05-2017, 01:38 PM
[quote=apachekid;2711810]311173311174311173311175311176311177[/quo