3 Bridgeports

[gorillapowered]

3 Mercury Bridgeports -- very clean -- they have been sitting in a shop attic for years -- came off a 30+ foot cat boat -- all engines were purchased together in April 1990 -- EFI engines with computers and CLE lower units -- offshore midsections: two 20 inch one 25 inch (center engine) -- engines are clean, have never been a part or blown up, little if any corrosion -- bone stock -- $15k for all 3 any questions (646)235-5255

306303306304306305306306306307

[Hot Shot Merc]

Thats awesome. great find. Is it just an odd angle or does this motor have a window in the block port side down low under the head? Looks like a hole to me

306310306308

[capteliminator]

Looks like grease or oil stain.

[gorillapowered]

Definitely not a window. Must just be some grease

[PARKER RABE]

Love those cowling scowling s

[Cp]

I've run beside 1 of these motors and couldn't hear for hours. I bet 3 would really howl!

[sundancekid]

Would you separate the 25" motor, what rotation is the 25, and trim pump come with? I have somebody that may be interested in it.

[gorillapowered]

Sundance, The 25" is regular rotation with a extension plate and obviously a 25" shaft on the CLE lower. I would separate it if you got somebody interested. Give me a call and let me know. Thanks

[85daytona]

what's the hp on these?

[gorillapowered]

The Bridgeport EFI are 240hp

[Scream And Fly]

These are nice. They have the latest model of the 'spine' midsection with the integrated lower mounts that were part of the midsection casting. That's my favorite midsection of all time, and my favorite motor. Very rare to find Bridgeports this nice. Look at those mint CLE cases too. These engines have 'rare' written all over them. Very good buy. If I had the time to run my boat regularly (or at all) I would buy one of these to go along with the BP on my boat now as a spare. These are just so hard to come by like this.

Also, I was pretty sure that the latest Bridgeport EFI engines (which these are) were 245hp, but I could be wrong.

Greg

[Capt.Insane-o]

These are nice. They have the latest model of the 'spine' midsection with the integrated lower mounts that were part of the midsection casting. That's my favorite midsection of all time, and my favorite motor. Very rare to find Bridgeports this nice. Look at those mint CLE cases too. These engines have 'rare' written all over them. Very good buy. If I had the time to run my boat regularly (or at all) I would buy one of these to go along with the BP on my boat now as a spare. These are just so hard to come by like this.

Also, I was pretty sure that the latest Bridgeport EFI engines (which these are) were 245hp, but I could be wrong.

Greg

*Yawn* I'd take a good 'ol boy 225 PM thank you pleez! :)

[pyro]

So, How much for one 20" motor?

[gorillapowered]

Thanks Greg! appreciate YOUR imput

[gorillapowered]

got someone for the 2 20". The 25" center motor has a extension plate that can be remove to make it a 20" but the shaft would have to be changed to a 20" on the CLE. I will sell the 25" Bridgeport for $4500. Thanks

[pyro]

Might be better off parting out the lower and clamp/mid. Then we can strike a deal on the powerhead. :D

[hydroguy85]

How much no center pice or gear case I have a 20 4 hole cle

[PARKER RABE]

if those motors are 1990 those are the wrong cowlings......those shown in the pic are from 1981 to 1985

[gorillapowered]

the date on all 3 blocks are 4/1990.... I don't think the early engines 81-85 were EFI

[pyro]

They are probably older motors with newer horn powerheads. Common.

[PARKER RABE]

They had efi in 84 they were down drafts, those being 1990 should have the Bridgeport cowlings

[TRIPLES]

Are all 3 still available

[gorillapowered]

all 3 still available

[JUPITER PULSARE]

Wish I had the extra $$ right now. These motors would be killer on my 28' Checkmate!!