superboattwin250
08-30-2014, 08:30 AM
Here is a list of everything that must go. I'm located in ct and you can pick up any parts locally that you are intersted in. All prices are plus shipping. I tried to list the parts the best I could. Please call if you want pictures of a part. It would be to many pictures to post of all this stuff. Reason for all these parts to go it to buy a new 300xs. Thanks for looking mark
3.0 liter parts first
1- 1998 250 efi cowl $200
1- set of 3.0 pans for the above cowl. $75
1- 3.0 liter 3 ram trim assembly. $150
1- 25 inch mid $100
1- 225hp opti tuner / plate $125
1- 3.0 lower unit case for parts only $75
1- 3.0 sei lower 25 inch rh. Skeg is shortened just a little. Bought new in 2010. $400
2.0/2.4/2.5 parts
1- green flywheel $20
1- red flywheel $25
4- mid section 20 inch. All are drilled out. $50 each
2- 5 peddle carb plates $25 each
1- 7 peddle carb plate $ 50
lots of 5 peddle reeds. Make offer
lots of coils. 10$ a peice
upper and lower bearing caps 10$
2.4 200 block. Needs sleeve $200
2.4 175 mariner front half $70
2.4 oiler crank. $150
2.4 pistons , rods. Have 4. Make offer
2.4 heads. Have 1 and 2 peice heads. $50 depending on which ones
carbs. All carbs are for parts only!! They have been sitting. Wh-40,WMh pumpers, wh22, wh, 33
also have a whole parts 2.4 liter motor. Tell me what you need.
Lower units
coned 1.87 20 inch rh $500
coned 2.00 20 inch rh $500
stock 1.87 20 inch rh $300
Stock 1.87 25 inch rh. Can be cut to 20 $300
props
All are small shaft Merc.
30 mazco re3 $200
28 offshore cut chopper $250
22 chopper $200
Hi po parts.
1- 5250 big rod $75
1- new style smooth back offshore mid complete 1 peice plate, tuner, trim. Awesome shape. 1750$
1- 260 mariner cowl bucket. 2.5 efi. Cowl, pan, skirt, and bracket. $650
1- trim pump with lines. It's old but works. $100
Best to call mark. 860 202 4683. Can text or email pictures or come to the garage and check them out.
3.0 liter parts first
1- 1998 250 efi cowl $200
1- set of 3.0 pans for the above cowl. $75
1- 3.0 liter 3 ram trim assembly. $150
1- 25 inch mid $100
1- 225hp opti tuner / plate $125
1- 3.0 lower unit case for parts only $75
1- 3.0 sei lower 25 inch rh. Skeg is shortened just a little. Bought new in 2010. $400
2.0/2.4/2.5 parts
1- green flywheel $20
1- red flywheel $25
4- mid section 20 inch. All are drilled out. $50 each
2- 5 peddle carb plates $25 each
1- 7 peddle carb plate $ 50
lots of 5 peddle reeds. Make offer
lots of coils. 10$ a peice
upper and lower bearing caps 10$
2.4 200 block. Needs sleeve $200
2.4 175 mariner front half $70
2.4 oiler crank. $150
2.4 pistons , rods. Have 4. Make offer
2.4 heads. Have 1 and 2 peice heads. $50 depending on which ones
carbs. All carbs are for parts only!! They have been sitting. Wh-40,WMh pumpers, wh22, wh, 33
also have a whole parts 2.4 liter motor. Tell me what you need.
Lower units
coned 1.87 20 inch rh $500
coned 2.00 20 inch rh $500
stock 1.87 20 inch rh $300
Stock 1.87 25 inch rh. Can be cut to 20 $300
props
All are small shaft Merc.
30 mazco re3 $200
28 offshore cut chopper $250
22 chopper $200
Hi po parts.
1- 5250 big rod $75
1- new style smooth back offshore mid complete 1 peice plate, tuner, trim. Awesome shape. 1750$
1- 260 mariner cowl bucket. 2.5 efi. Cowl, pan, skirt, and bracket. $650
1- trim pump with lines. It's old but works. $100
Best to call mark. 860 202 4683. Can text or email pictures or come to the garage and check them out.