PDA

View Full Version : Anyone ever have this problem?



Blue Stream
07-18-2013, 10:04 AM
Mounting up my 15 midsection to the SeaStar and the pivot bracket is 2 inches short.

Is there a bracket for this?

Thx

http://im1.shutterfly.com/media/47a3d939b3127ccef3f0d46f1ca800000030O01BcOWTls5Zg9vPhI/cC/f%3D0/ls%3D00309069298020130718123531728.JPG/ps%3D50/r%3D0/rx%3D720/ry%3D480/

albypine
07-18-2013, 11:11 AM
What's up with that tiller arm ? Looks like someone hacked all the meat off:eek:

DOC W
07-18-2013, 11:39 AM
looks like someone changed the tiller arm from an older mid with out the extra set back

Blue Stream
07-18-2013, 10:41 PM
Tiller arm is the same all the way around. Just look bad in picture because of the paint.

albypine
07-18-2013, 11:36 PM
Look at a real off shore tiller then look at that picture . They have the corners cut off and super thin where the dead mans bolt goes ..

stoker2001
07-18-2013, 11:56 PM
that appears to be a vintage tiller arm 1979?my bud has same setup on his 1979 avenger

stoker2001
07-18-2013, 11:58 PM
http://www.screamandfly.com/showthread.php?268390-Seastar-cylinder-on-a-1978-2-4l&p=2495206&highlight=#post2495206post#5

5

stoker2001
07-19-2013, 12:02 AM
i think your gonna need Seastar # HC5342 or earlier model??

Dave Strong
07-19-2013, 12:54 AM
Factory 15" mids have an extra 2" of set back built in not sure if the tiller arm is extended.

Dave

Blue Stream
07-19-2013, 07:11 AM
Look at a real off shore tiller then look at that picture . They have the corners cut off and super thin where the dead mans bolt goes ..

Yes compared to a new one this one is not as beefy. I was saying it is all the same around but looks factory, just don't know from how long ago.

Anyone have a 280SS Tiller for sale?:D

Coupe427
07-19-2013, 07:58 AM
Is yours a factory can or cut down to 15"? As Dave stated the factory 15" mid has 2" extra setback built into the bracket . I would have to measure one but would think the tiller would have to be 2" longer to accommodate it.

Blue Stream
07-19-2013, 08:12 AM
Can was cut by Powell, the clamp is from a 280 I think.

http://im1.shutterfly.com/media/47a3d939b3127ccef3f0b6541ca200000030O01BcOWTls5Zg9vPhI/cC/f%3D0/ls%3D00309069298020130718123530995.JPG/ps%3D50/r%3D0/rx%3D720/ry%3D480/http://im1.shutterfly.com/media/47a3d806b3127ccef322bfd807ec00000030O01BcOWTls5Zg9vPhI/cC/f%3D0/ls%3D00309069298020130627150956317.JPG/ps%3D50/r%3D0/rx%3D550/ry%3D400/

Coupe427
07-19-2013, 08:25 AM
From that picture it definitely looks too short.

found one of mine.

http://i160.photobucket.com/albums/t171/coupe427/9462B97B-742A-4AC3-9DF4-377538BC1CA2-3824-000002CBBC6FCC03_zpsd3cfb5ea.jpg (http://s160.photobucket.com/user/coupe427/media/9462B97B-742A-4AC3-9DF4-377538BC1CA2-3824-000002CBBC6FCC03_zpsd3cfb5ea.jpg.html)

Blue Stream
07-19-2013, 08:26 AM
Yes no doubt

Blue Stream
07-21-2013, 12:26 AM
Nice pic, wish mine looked like that : )